EE
NN
GInstallation GuideG
LL
II
SS
e Disconnect the cable from the negative - battery
HCaution:OverviewH
terminal (see caution below).
e This unit operates with a 12 V DC
45 WARNINGThis product should be installed by a professional. 46e Unit should be installed in a horizontal position
negative ground auto battery system only.
However, if you plan to install this product yourself,
with the front end up at a convenient angle, but
This installation information is Do not attempt to use it in any other system.
your Ţ rst step is to decide where to install it. The
not more than 30o.
designed for experienced installers Doing so could cause serious damage.
instructions in these pages will guide you through
and is not intended for non-technical the remaining steps:
individuals. It does not contain (Please refer to the OWARNING� statement.)
Installation Hardware
warnings or cautions of potential
e Identify and label the car wires.
Less than 30o
dangers involved in attempting to e Connect the car wires to the wires of the power
No.ItemDiagram QOty
install this product.connector.
1Mounting collar1
e Install the unit in the dashboard.
Any attempt to install this product in
e Check the operation of the unit.
Caution:
a motor car by anyone other than a
2Hex. nut (5 mm�)1e If your car is equipped with air bags and/or
qualiŢ ed installer could cause damage If you encounter problems, please consult your
anti-theft systems speciŢ c procedures may
to the electrical system and could result nearest professional installer.be required for connection and disconnection
3Rear support strap1
in serious personal injury or death.Before you begin installation, look for the items of the battery to install this product.
which are packed with your unit.e Before attempting installation of this
If your car is equipped with air bags 4Tapping screw1
electronic component contact your car
e Warranty Card... Fill this out promptly.
and/or anti-theft systems speciŢ c (5 mmk 16 mm)
dealer or manufacturer to determine the
e Panasonic Servicenter List for Service
procedures may be required for 5Mounting bolt 1required procedure and strictly follow their
Directory... Keep for future reference in case the
connection and disconnection of the (5 mm�)instructions.
product needs servicing.
e FAILURE TO FOLLOW THE PROCEDURE MAY
battery to install this product. 6Power connector1e Installation Hardware... Needed for in-dash
RESULT IN THE UNINTENDED DEPLOYMENT
installation.
Before attempting installation of this OF AIR BAGS OR ACTIVATION OF THE
7Trim plate1
electronic component contact your car ANTI-THEFT SYSTEM RESULTING IN DAMAGE
dealer or manufacturer to determine TO THE VEHICLE AND PERSONAL INJURY.
8Lock cancel plate2Dashboard SpeciŢ cations
the required procedure and strictly
3Note:follow their instructions.Thickness Min. /16q (4.75 mm)
7e Various settings that have been stored in the
Max. /32q (5.56 mm)
FAILURE TO FOLLOW THE PROCEDURE memory in other on-board equipment (car
MAY RESULT IN THE UNINTENDED Required Toolsnavigation etc.) may be lost if the battery
3
2 /32q (53 mm)terminals are disconnected.
DEPLOYMENT OF AIR BAGS OR YouOll need a screwdriver, a 1.5 V AA battery, and
Therefore, we recommend to make a record of
ACTIVATION OF THE ANTI-THEFT the following:
5or to back up the settings before disconnecting
7 /32q (182 mm)
SYSTEM RESULTING IN DAMAGE TO 12 V DC Electrical tapeSide-cut
the terminals.
THE VEHICLE AND PERSONAL INJURY.Test bulbpliersAfter completing installation of the main unit,
set the equipment again according to the
Preparation
record.
Dashboard Installation
e We strongly recommend that you wear gloves
for installation work to protect yourself from Installation Opening
injuries.
3
2/q (53 mm)
e When bending the mounting tabs of the 32
mounting collar with a screwdriver, be careful
not to injure your hands and Ţ ngers.75/32q (182 mm)
This unit can be installed in any dashboard having
an opening as shown above. The dashboard should
37
be /16q (4.75 mm)�/32q (5.56 mm) thick in order to
be able to support the unit.
6465
CQ-C9800/9700UCQ-C9800/9700U |