Water Pressure
Electrical Requirements
A cold water supply with water pressure of between 30 and
120 psi (207 - 827 kPa) is required to operate the water dispenser WARNING
and ice maker. If you have questions about your water pressure,
call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 - 827 kPa).
If a reverse osmosis water filtration system is connected to your
Electrical Shock Hazardcold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).
Plug into a grounded 3 prong outlet.
If the water pressure to the reverse osmosis system is less than
Do not remove ground prong.40 to 60 psi (276 - 414 kPa):
Check to see whether the sediment filter in the reverse Do not use an adapter.
osmosis system is blocked. Replace the filter if necessary.
Do not use an extension cord.Allow the storage tank on the reverse osmosis system to refill
after heavy usage.Failure to follow these instructions can result in death,
fire, or electrical shock.If you have questions about your water pressure, call a licensed,
qualified plumber.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.Connect the Water Supply
Recommended Grounding MethodRead all directions before you begin.
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded IMPORTANT: If you turn the refrigerator on before the water line is
electrical supply is required. It is recommended that a separate connected, turn the ice maker OFF.
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an Connect to Water Line
extension cord.
NOTE: Before performing any type of installation, cleaning, or 1. Unplug refrigerator or disconnect power.
removing a light bulb, turn the control (Thermostat, Refrigerator or 2. Turn OFF main water supply. Turn ON nearest faucet long
Freezer Control depending on the model) to OFF and then enough to clear line of water.
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source and 3. Locate a 1" to 11D?" (1.25 cm to 3.18 cm) vertical cold water
reset the control (Thermostat, Refrigerator or Freezer Control pipe near the refrigerator.
depending on the model) to the desired setting.IMPORTANT:
Make sure it is a cold water pipe.
Water Supply RequirementsHorizontal pipe will work, but drill on the top side of the
Gather the required tools and parts before starting installation. pipe, not the bottom. This will help keep water away from
Read and follow the instructions provided with any tools listed the drill and normal sediment from collecting in the valve.
here.4. Determine the length of copper tubing you need. Measure
TOOLS NEEDED: from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1D?"
Flat-blade screwdriver1D?" Drill bit
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both
wD??" and 1D?" Open-end or two Hand drill or electric drill ends of copper tubing are cut square.
adjustable wrenches(properly grounded)5. Using a grounded drill, drill a 1D?" hole in the cold water pipe
you have selected. 1D?" nut driver
A
NOTE: Your refrigerator dealer has a kit available with a 1D?"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. B
G
Before purchasing, make sure a saddle-type valve complies with C
your local plumbing codes. Do not use a piercing-type or 3D??"
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
IMPORTANT:F ED
All installations must meet local plumbing code requirements.A.Cold water pipeE.Compression sleeve
B.Pipe clampF.Shutoff valve
Use copper tubing and check for leaks. Install copper tubing C.Copper tubingG.Packing nut
only in areas where the household temperatures will remain
above freezing.D.Compression nut
4 |
ACEC
WHIRLPOOL
