3-1-2. Precautions on Adjusting
1) The adjustments of this unit are performed in the VTR mode or
camera mode.Note 1:Setting the OForced VTR Power ON� Mode (VTR Mode)
To set to the VTR mode, set the power switch to OVTR� (or1) Set data: 01 to page: 1, address: 00.
PLAYER) or set the OForced VTR Power ON Mode� using the2) Set data: 02 to page: D, address: 10, and press the PAUSE
adjusting remote commander (Note 1).button of the remote commander.
To set to the camera mode, set the power switch to OCAMERA�The above procedure will enable the VTR power to be
or set the OForced Camera Power ON Mode� using the adjustingturned on with the VK4800 operation switch block
remote commander (Note 2).removed.
After completing the adjustments, be sure to exit the OForcedAfter completing adjustments, be sure to exit the OForced
VTR Power ON Mode� or OForced Camera Power ON Mode�.VTR Power ON� mode.
(Note 3)Note 2:Setting the OForced Camera Power ON� Mode (Camera
2) Because the cabinet (L) is attached with the FZ4800 board (CCMode)
DOWN switch, zoom switch), be sure to connect FZ4800 board1) Set data: 01 to page: 1, address: 00.
when recording and playing back. If the cabinet (L) comes in the2) Set data: 01 to page: D, address: 10, and press the PAUSE
way, remove FZ4800 board from the cabinet (L), and connect tobutton of the remote commander.
CN6103 (5P, 0.5mm) of the MR-36 board. Set the CC DOWNThe above procedure will enable the camera power to
switch to ON normally (pressed state), and turn it OFF only whenbe turned on with the VK4800 operation switch block
ejecting.removed.
3) The viewfinder need not be connected (except during battery endAfter completing adjustments, be sure to exit the OForced
adjustment). Disconnect the following connector when adjusting.VTR Power ON� mode.
1. CN1000 of VC-183 board (20P, 0.5mm, B-B)Note 3:Exiting the OForced Power ON� Mode
4) The lens block need not be connected in adjustments other than1) Set data: 01 to page: 1, address: 00.
the camera system adjustments (except during battery end2) Set data: 00 to page: D, address: 10, and press the PAUSE
adjustment). Disconnect the following connector when adjusting.button of the remote commander.
1. CN200 of VC-183 board (50P, 0.5mm, B-B)3) Set data: 00 to page: 1, address: 00.
5) If ejection need not be performed, the VK4800 control switch
block (power switch, eject switch, start/stop switch, VTR function
switch) need not be connected as long as the OForced Power ON
Mode� is set.
Disconnect the following connector when removing it.
1. CN2300 of VC-183 board (20P, 0.5mm)
After completing adjustments, be sure to exit the OForced Power
ON Mode�.
6) When opening the MR-36 board, use the following extension
cord.
1. J-6082-374-A (18P, 0.5mm)
7) When removing the cabinet (R) (DD-91 board, LCD block,
microphone, speaker, ME4800 switch block), only the DD-91
board will need to be connected to operate the unit. Remove the
DD-91 board from the cabinet (R), and connect it to CN6200 of
the VC-183 board (60P, 0.5 mm, B-B) and CN6102 of the MR-
36 board (30P, 0.5mm, B-B). When removing the LCD block,
microphone, speaker, and ME4800 switch block, disconnect the
following connectors.
1. CN2301 of VC-183 board (5P, 0.5 mm)
(ME4800 switch block)
2. CN4700 of VC-183 board (4P, 1.0 mm) (microphone)
3. CN4701 of VC-183 board (2P, 1.0 mm) (speaker)
4. CN1001 of VC-183 board (6P, 1.0 mm) (LCD block)
5. CN1002 of VC-183 board (11P, 1.0 mm) (LCD block)
8) If the DD-91 board is disconnected from the VC-183 board, the
lithium 3V power supply will also be disconnected and all data
set by the user such as date, time, menu, etc. will be erased. Set
these data again after completing the adjustments.
6-37 |
ACEC
SONY
