MAN-DEH-P7900UB-GB.fm Page 25 Wednesday, February 21, 2007 11:20 AM
Operating this unit
4. Push MULTI-CONTROL up or down to adjust the level of the equalizer band.Adjusting subwoofer settings
Each time MULTI-CONTROL is pushed up or down, the level of the equalization band When the subwoofer output is on, you can adjust the cut-off frequency and the output
increases or decreases.level of the subwoofer.
+6 to -6 is displayed as the level is increased or decreased.1. Use MULTI-CONTROL to select Sub W.2.
? You can then select another band and adjust the level.? You can also select the subwoofer setting menu by pressing SW on the unit.
5. Press BAND to cancel the 7-band graphic equalizer adjustment.? When the subwoofer output is on, you can select Sub W.2.
Adjusting loudness2. Push MULTI-CONTROL left or right to select cut-off frequency.
Each time MULTI-CONTROL is pushed left or right, cut-off frequencies are selected
Loudness compensates for deficiencies in the low- and high-sound ranges at low
volume.in the following order:
1. Use MULTI-CONTROL to select LOUD.50Hz - 63Hz - 80Hz - 100Hz - 125Hz
Only frequencies lower than those in the selected range are outputted from the
2. Press MULTI-CONTROL to turn loudness on.subwoofer.
Loudness level (e.g., Mid) appears in the display.
3. Push MULTI-CONTROL up or down to adjust the output level of the subwoofer.
? To turn loudness off, press MULTI-CONTROL again.
Each time MULTI-CONTROL is pushed up or down, subwoofer level increases or
3. Push MULTI-CONTROL left or right to select a desired level.decreases. +6 to -24 is displayed as the level is increased or decreased.
Each time MULTI-CONTROL is pushed left or right, level is selected in the following
Boosting the bass
order:
Bass boost function boosts the bass level of sound lower than 100 Hz. The more the
Low (low) - Mid (mid) - High (high)
bass level is increased, the more the bass sound is emphasized and the entire sound
Using subwoofer outputbecomes powerful. When using this function with the subwoofer, the sound under the
cut-off frequency is boosted.
This unit is equipped with a subwoofer output which can be turned on or off.
1. Use MULTI-CONTROL to select Bass.
1. Use MULTI-CONTROL to select Sub W.1.
? You can also select the bass boost setting by pressing and holding SW.
? You can also select the subwoofer setting menu by pressing SW on the unit.
2. Push MULTI-CONTROL up or down to select a desired level.
2. Press MULTI-CONTROL to turn subwoofer output on.
0 to +6 is displayed as the level is increased or decreased.
Normal appears in the display. Subwoofer output is now on.
? To turn subwoofer output off, press MULTI-CONTROL again.Using the high pass filter
3. Push MULTI-CONTROL left or right to select the phase of subwoofer output.When you do not want low sounds from the subwoofer output frequency range to play
from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies
Push MULTI-CONTROL left to select reverse phase and Reverse appears in the
display. Push MULTI-CONTROL right to select normal phase and Normal appears in higher than those in the selected range are outputted from the front or rear speakers.
the display.1. Use MULTI-CONTROL to select HPF.
2. Press MULTI-CONTROL to turn high pass filter on.
ENGLISH
80Hz appears in the display. High pass filter is now on.
? If the high pass filter has been previously adjusted, the frequency of that previously
selected will be displayed instead of 80Hz.
? To turn high pass filter off, press MULTI-CONTROL again.
25 |
ACEC
PIONEER
