DLA-M4000LE DLA-M4000LU
Controls and Features (cont.)Controls and Features (Cont.)
Connector PanelRemote Control Unit
12
1
r
ALIGN.QUICKAV HIDEOPERATE
Y/CVIDEOe2
PRESETPAGE BACK
8RGBRGB IN-1
wLOCKUNLOCK3
LENSMENU/EN
qTER
RRGB IN-2EXT. INY4
7GH/CSPB/B-Y3
AVRGB/COMPUTER
p5
BVPR/R-Y
UT+
SHIFT ZOOM FOCUS96
REMOTELENSDW�
RGB OUTCONTROL
RS-232C8
6 54
1Y/C (S video) input terminal (Mini DIN 4 pin)7RGB IN (RGB input) -2 terminal (BNC)
Connect this terminal to the S video output terminal of aThese are input terminals for analog RGB signals, vertical
video deck, etc.sync (V) signals, and horizontal sync (H) signals / composite
* This terminal can be used if a video board (PK-G1signals(Cs). Devices which have analog RGB signal output101D)7
No.51666sold separately has been installed. The terminal was notterminals can be connected.
provided when the projector was shipped from the factory * Input of external sync signals is automatically.
detected.
2VIDEO (composite video) input terminal (BNC)Detection of H/V signals or Cs signals causes automatic1Remote controlOs signal transmitter6FOCUS (+/�) button
Connect this terminal to the composite video output terminalswitch to external sync. The priority order is H/V > Cs.Use these buttons to adjust the focus of the projected
of a video deck, etc.2OPERATE buttonpicture.
* This terminal can be used if a video board (PK-G1CAUTION101D)To turn on or off the power, press this button for one or+: The focus point becomes more distant.
sold separately has been installed. The terminal was notYWhen computer-related signals are input, the uppermost edgemore seconds.�: The focus point becomes nearer.
provided when the projector was shipped from the factory.*About 30 seconds after the power has turned on, video
of the screen may appear bowing if the sync signal input isimage will appear on the screen.7REMOTE terminal
composite sync (Cs) or G on sync signal. In that case, use
3Y, PB/B-Y, PR/R-Y input terminals (BNC)Use a remote control cable to connect between the
These are input terminals for component (Y, B-Yseparate sync signals for vertical sync (V) and horizontal sync, R-Y)3PAGE BACK buttonprojector and the remote control. For details, refer to
signals or DTV-format (YB, PR, P) signals.(H).While no menu is displayed, pressing this button causes aOConnecting to Devices which Control the Projector� on
Device with component signal output terminals, such as8RGB IN (RGB input) -1 terminal (D-sub 3- row 15 pin)direct channel to be displayed.page 22.
for NTSC and DTV-format, can be connected.This is an input terminal (PC) dedicated for computerMemo
8ZOOM (T/W) button
*For details about DTV-format signals (480i, 480p, 720p,signals (RGB video signals and sync signals).Direct channel display:
Use these buttons to increase or decrease the screen size.
1080i) compatible with this unit, refer to page 66.Connect the display output terminal of the computer to thisA direct channel display allows you to switch between chan-
(They can only be used when a zoom lens is used.)
terminal. When a Macintosh or PC-9801/9802 seriesnels which have lines and sources registered. For details,
T: The screen size decreases.
4REMOTE terminal (mini jack)computer is to be connected, use a suitable conversionrefer to OSwitching channels using a direct channel� (page
W: The screen size increases.
This terminal is used to directly connect the remote con-adapter separately available.52).
trol to the projector. Use the remote control cable supplied.
CAUTION9SHIFT (U/D) button
An infrared remote control extension unit can also be con-4 MENU/ENTER buttonUse these buttons to adjust the height of the projection
nected to the jack.YWhen computer-related signals are input, the uppermost edgeUse this button to display the main menu, or while the mainscreen when projectors are used in a stack configuration.
of the screen may appear bowing if the sync signal input ismenu is displayed, use the button to select an item to adjust
5RS-232C terminal (D-sub 9 pin)composite sync (Cs) or G on sync signal. In that case, useor make adjustment. While the main menu is displayed,U: Moves the screen upwards.D: Moves the screen downwards.
This is a RS-232C interface-specified terminal. separate sync signals for vertical sync (V) and horizontal syncThispressing MENU/ENTER displays a details setting
projector can be controlled by a computer connected(submenu) if the selected item has a details setting.
(H).
externally.For how to operate the buttons, see page 13.
6RGB OUT (RGB output) terminal (D-sub 3-row 15 pin)5RGB / COMPUTER button
The computer input signal projected on the screen is output.Use this button to select the devices connected to the
A display unit can be used by connecting it to this terminal.projectorOs RGB IN (RGB input) -1 and -2 input terminals.
Each time you press the button, the selection changes as
follows:RGB 1RGB 2
1011 |
ACEC
JVC
