Safety Precaution
� Slots and openings in the cabinet are provided for ventilation.� The product should be placed more than one foot away from
These ensure reliable operation of the product and protect itheat sources such as radiators, heat registers, stoves, and
from overheating. These openings must not be blocked orother products (including amplifiers) that produce heat.
covered. (The openings should never be blocked by placing� When connecting other products such as VCROs, and per-
the product on bed, sofa,rug, or similar surface. It should notsonal computers, you should turn off the power of this prod-
be placed in a built-in installation such as a bookcase or rackuct for protection against electric shock.
unless proper ventilation is provided and the manufacturerOs� Do not place combustibles behind the cooling fan. For ex-
instructions have been adhered to.)ample, cloth, paper, matches, aerosol cans or gas lighters
For proper ventilation, separate the product from other equip-that present special hazards when over heated.
ment, which may prevent ventilation and keep a distance of� Do not look into the projection lens while the illumination lamp
more than 11-7/8� (30 cm).is turned on. Exposure of your eyes to the stronglight can
� This product should be operated only with the type of powerresult in impaired eyesight.
source indicated on the label. If you are not sure of the type of� Do not look into the inside of this unit through vents (ventila-
power supply to your home, consult your product dealer ortion holes), etc. Do not look at the illumination lamp directly
local power company.by opening the cabinet while the illumination lamp is turned
� This product is equipped with a three-wire plug. This plug willon. The illumination lamp also contains ultraviolet rays and
fit only into a grounded power outlet. If you are unable to in-the light is so powerful that your eyesight can be impaired.
sert the plug into the outlet, contact your electrician to install� Do not drop, hit, or damage the light-source lamp (lamp unit)
the proper outlet. Do not defeat the safety purpose of thein any way. It may cause the light-source lamp to break and
grounded plug.lead to injuries. Do not use a damaged light source lamp. If
�Power-supply cords should be routed so that they are notthe light-source lamp is broken, ask your dealer to repair it.
likely to be walked on or pinched by items placed upon orFragments from a broken light-source lamp may cause inju-
against them. Pay particular attention to cords at doors, plugs,ries.
receptacles, and the point where they exit from the product.� The light-source lamp used in this projector is a high pres-
�For added protection of this product during a lightning storm,sure mercury lamp. Be careful when disposing of the light-
or when it is left unattended and unused for long periods ofsource lamp. If anything is unclear, please consult your dealer.
time, unplug it from the wall outlet and disconnect the cable� Do not Oceiling-mount� the projector to a place which tends to
system. This will prevent damage to the product due to light-vibrate; otherwise, the attaching fixture of the projector could
ning and power line surges.be broken by the vibration, possibly causing it to fall or over-
� Do not overload wall outlets, extension cords, or convenienceturn, which could lead to personal injury.
receptacles on other equipment as this can result in a risk of� Use only the accessory cord designed for this product to pre-
fire or electric shock.vent shock.
�Never push objects of any kind into this product through open-The power supply voltage rating of this product is AC 120 V,
ings as they may touch dangerous voltage points or short outAC 100 V� AC 240 V, the power cord attached conforms to
parts that could result in a fire or electric shock.the following power supply voltage. Use only the power cord
ENGLISH
Never spill liquid of any kind on the product.designated by our dealer to ensure Safety and EMC.
� Do not attempt to service this product yourself as opening orWhen it is used by other power supply voltage, power cable
removing covers may expose you to dangerous voltages andmust be changed.
other hazards. Refer all service to qualified service person-Ensure that the power cable used for the projector is the cor-
nel.rect type for the AC outlet in your country.
� Unplug this product from the wall outlet and refer service toConsult your product dealer.
qualified service personnel under the following conditions:
a) When the power supply cord or plug is damaged.
b) If liquid has been spilled, or objects have fallen on the prod-
uct.Power cord
c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper adjust-
ment of controls may result in damage and will often re-
For United KingdomFor European
quire extensive work by a qualified technician to restorecontinent countries
the product to normal operation.
e) If the product has been dropped or damaged in any way.Power cord
f ) When the product exhibits a distinct change in performance
- this indicates a need for service.
� When replacement parts are required, be sure the service
technician has used replacement parts specified by the manu-Power supply voltage: AC 120 V
facturer or with same characteristics as the original part. Un-
authorized substitutions may result in fire, electric shock, or
*DO NOT allow any unqualified person to install the unit.
other hazards.
Be sure to ask your dealer to install the unit (eg. attaching it
� Upon completion of any service or repairs to this product, ask
to the ceiling) since special technical knowledge and skills
the service technician to perform safety checks to determine
that the product is in proper operating condition.are required for installation.
If installation is performed by an unqualified person, it may
cause personal injury or electrical shock.
3
02-05_Eng.p65302.10.4, 12:05 PM |
ACEC
JVC
