HeCFcadadecMagaeecIaeabeCFcad
The DM-3200 stores library settings, automation -When data, the etc. card tois formatted, move the cursor to The the DM-3200 on-screen does not automatically write to the CF card
gether in projects, which are stored on a CF card, MANAGEPROJECTSallowing button, and press ENTER .every time a change is made to the project. This is to avoid
the mix data for recording sessions to be transported easily unnecessary stressing of the card, which can cause premature
Note here is already an invisible project in the DM-3200
between different locations.failure of the card.
memory which has not been saved.
Use any CF card (Type I or Type Accordingly, when shutting down the DM-3200, to write the
Press the POD 1 switch (NEWPROJECT):
II). A card of at least -32MB capacdata currently in memory to the current project, press and
ity, such as the one supplied with the hold the SHIFT and CTRL keys, and press the ALT key.
DM-3200, is recommended.
T?eCFcaAdOAbef�A?aII?edbe
f�AeOAe�?I?EI?eDM?��ääE��Ie
I?aIE I?e AO??Ź?ed caAd ?AE aŹAeadŢE+
f�A?aIIed?:
Press the LIBRARY key, and then
press the POD 1 key, and turn the
The display shows a popup, asking if you are sure you want to
POD 1 encoder below the display so
that the UTILITY option in the pop-up turn off the DM-3200. ENTERPress to continue.
menu is highlighted.You then see a message showing that it is safe to turn off the
DM-3200 (or you can reboot it ALT using + STOP the + PLAY
Press ENTER for the UTIL-Use the cursor keys and wheel to set the sampling keys).frequency
ITY screen.and surround mode. ENTERUse to conrm these entries You as can also write the current data to the currently loaded
you make them.project on the CF card at any MANAtime, GEPROJECTfrom the
Use the cursor keys to
screen ALT( + PROJECT key, followed MANAby GEPRJ. (POD
move the cursor to the on-Move the cursor to the NEWon-screen PROJECTCREATE button
scren CFUTIL button. Press and press ENTER . The screen changes to show the project switch 2).
ENTER.naming utility:
Use the cursor keys to move NAMEaround and MEMOthe elds.
Use the cursor keys to move the cursor FORMAto T the on-screen The current project is marked with an inverted C by its name.
button, and press ENTER . Use the wheel to select a character from the list, and the
Note that if the DM-3200 is started without the current data
ENTER key to enter the selected character at the cursor.
having been saved to card, a popup message reminds you of
Use the special INSER Tand DELETE labels as if they are characters
the fact. You then have the choice of loading the last project
(highlight and ENTER ).with or without the unsaved data.
If there are projects already on the card, -use C?athe ?g??POD gA�4 ŤeencIA,eIc°
coder to select a project dNAME and . dThe MEMO labels copy
A popup message appears. Press ENTER to continue.Use the POD 4 encoder to scroll through the list of projects
over the selected project name and note as templates.
Another popup message appears, warning you that all data on a card. When a project is selected in the list at the right of
When the name and note are complete, press the the POD screen, 2 use the on-screen buttons under the list to load
will be erased. Press ENTER to format the card.
switch (CREATE) to create the new project.(LOAD), protect PROTECT(), rename RENAME( ) or delete DELETE) ( the
While the card is being formatted, a message briey appears.
- See Section 2, Basic operational concepts Own-highlighted project.of the
Do not remove the card or turn off power while formatting
er?s Manual.
is going on. The Completedword appears on the display when - See Section 2, Basic operational Ownerconcepts ?s of the
formatting is complete on the display.Manual.
TASCAMDMQcRefeecePageTASCAMDMQcRefeecePageTASCAMDMQcRefeecePage4 |
ACEC
TEAC
