D-NF610/NF611
TABLE OF CONTENTSThis appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
1. SERVICING NOTEáááááááááááááááááááááááááááááááááááááááááááááááááááááááááá3
the rear exterior.
2. GENERALáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá4
3. DISASSEMBLYáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá5
4. ELECTRICAL ADJUSTMENTáááááááááááááááááááááááááááááááááááá8
5. DIAGRAMSáááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááááá10
CAUTION
5-1. Block Diagram
Use of controls or adjustments or performance of procedures� MAIN Section � ááááááááááááááááááááááááááááááááááááááááááááááááááááááá 11
other than those specified herein may result in hazardous� TUNER Section �ááááááááááááááááááááááááááááááááááááááááááááááááááááá 12
radiation exposure.
5-2. Printed Wiring Board
� MAIN Board (Side A)(1/2) � ááááááááááááááááááááááááááááááááááá 13
5-3. Printed Wiring BoardFlexible Circuit Board Repairing
� MAIN Board (Side A)(2/2) � ááááááááááááááááááááááááááááááááááá 14YKeep the temperature of the soldering iron around 270 uC dur-
5-4. Printed Wiring Board � MAIN Board (Side B)(1/2) � 15ing repairing.
5-5. Printed Wiring Board � MAIN Board (Side B)(2/2) � 16Y Do not touch the soldering iron on the same conductor of the
5-6. Schematic Diagram � MAIN Board (1/5) � ááááááááááááááá 17circuit board (within 3 times).
5-7. Schematic Diagram � MAIN Board (2/5) � ááááááááááááááá 18Y Be careful not to apply force on the conductor when soldering
5-8. Schematic Diagram � MAIN Board (3/5) � ááááááááááááááá 19or unsoldering.
5-9. Schematic Diagram � MAIN Board (4/5) � ááááááááááááááá 20
5-10.Schematic Diagram � MAIN Board (5/5) � ááááááááááááááá 21Notes on chip component replacement
5-11.IC Block Diagram ááááááááááááááááááááááááááááááááááááááááááááááááááááááá 22YNever reuse a disconnected chip component.
5-12.IC Pin Function Descriptions áááááááááááááááááááááááááááááááááááááá 27Y Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
6. EXPLODED VIEWSáááááááááááááááááááááááááááááááááááááááááááááááááááááá32
Notes on the power source
7. ELECTRICAL PARTS LISTááááááááááááááááááááááááááááááááááááááá35Disconnect all power sources when the CD player is not used for a long time.
Unleaded solderOn AC power adaptor
Boards requiring use of unleaded solder are printed with the lead-Y Use only the AC power adaptor supplied.
free mark (LF) indicating the solder contains no lead.If your CD player is not supplied with the one, use the AC-E45HG AC
power adaptor. Do not use any other AC power adaptor. It may cause a(Caution: Some printed circuit boards may not come printed with
malfunction.
the lead free mark due to their particular size.)
Polarity of the plug
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Y Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
Y Do not touch the AC power adaptor with wet hands.
applied to the solder joint for a slightly longer time.Y Connect the AC power adaptor to an easily accessible AC outlet. Should
Soldering irons using a temperature regulator should be set toyou notice an abnormality in the AC power adaptor, disconnect it from
about 350°C.the AC outlet immediately.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Y Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
Y Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!ATTENTION AU COMPOSANT AYANT RAPPORT
� LA S?CURIT?!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHLES COMPOSANTS IDENTIF?S PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSDIAGRAMMES SCH?MATIQUES ET LA LISTE DES PIéCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECRITIQUES POUR LA S?CURIT? DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERSREMPLACER CES COMPOSANTS QUE PAR DES PIéSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSDONT LES NUM?ROS SONT DONN?S DANS CE MANUEL OU
PUBLISHED BY SONY.DANS LES SUPP?MENTS PUBLI?S PAR SONY.
2 |
ACEC
SONY
