ENGLISH
10PLAYBACK11RECORDING
Y Switch on your amplifier or receiver.Y Switch on the source component (tuner, amplifier,
Music search systemCAUTION :
Y Set the TAPE MONITOR switch on your amplifier oretc.).In the recording mode, the variable speed mode
receiver to the TAPE position.The music search system detects blank sectionsY Set the TAPE MONITOR switch on your amplifier or
cannot be selected, and the mode is automatically
1. POWER(lasting for at least 4 seconds) between selections inreceiver to the SOURCE position.switched to the fixed speed mode.
Y Push the switch q to turn OON� (c) the power.order to locate the beginning of selections in theNOTE :Be careful not to erase important recordings by
forward or reverse direction.Y It is not possible to use both the BALANCEDmistake. Mis-erasing can be avoided by following
NOTE :1. To advance from the current selection to theINPUT and UNBALANCED INPUT jacks at thethe two steps below :
Y The display lights when the deck mechanism is
beginning of the next selection (CUE) :same time. Use the input selected with the1. If the play (0 or 1) while the O4� will light, the
being initialized. The deck will not operated
during initialization.Press the play (1) button @9 simultaneously withINPUT SELECT switch.tape will be recorded.
the fast forward (7) button @9. Press the play (0)2. If the play (0 or 1) and rec/rec mute (4) button
2. EJECTbutton @9 simultaneously with the rewind (6)1. POWERare pressed at the same time, the tape will be
Y Push the switch q to turn OON� (c) the power.recorded.
Y Press the eject (5) button @7 to open thebutton @9.
cassette compartment.The deck will skip the rest of the current selectionNOTE :3. Performing the record pause or the stop
and automatically resume play from the beginningoperation during recording will create a
3. Cassette compartment cover @8Y The display lights when the deck mechanism is
of the next selection.discontinuous portion in the recording signal.
Y Load the cassette tape.being initialized. The deck will not operatedThe previously recorded signal may remain after
2. To repeat playback from the beginning of theduring initialization.
4. DOLBY NR switch @2erasure at this connecting portion. Also, a very
current selection (REVIEW) :
Y For recordings made without Dolby NR, set toPress the play (1) button @9 simultaneously with2. EJECTsmall amount of the end portion of the previous
OOFF�.song may be erased.
the rewind (6) button @9. Press the play (0)Y Press the eject (5) button @7 to open the
Y For recordings made with Dolby B NR, set tobutton @9 simultaneously with the fast forwardcassette compartment.
OB�.
(7) button @9.CAUTION :
Y For recordings made with Dolby C NR, set toThe deck will rewind the tape to the beginning of3. Cassette compartment cover @8Y Do not turn off the power while the deck is
OC�.Y Make sure the erasure prevention tab has not
the current selection and automatically resume playoperating or being initialized. Doing so could
5. REV. MODE switch @0from that point.been removed from the cassette shell half.cause damage.
: To listen to one side onlyThis is very convenient for repeating playback of the4. DOLBY NR switch @2
: To listen to repeat playback of both sidecurrent selection.Y Select the Dolby NR type that suits the
recording.CAUTION :
6. OUTPUT switch !9Y This set has a quick reverse function. When
Y Select �SEP.� to output only the deck signals,Notes on Music Search Operation :5. REV. MODE switch @0recording on an already recorded tape, some of
The search functions operates by detecting: To record on only one side
OMIX� to output the mixed deck and CD signalsthe old recording at the beginning of the reverse
comparatively long, blank sections approximately 4
from the MIX outputs.to 5 seconds long, in between recorded selections.: To continuously record on both sidesside of the tape is not erased, so erase it before
7. Play (0 or 1) button @9Therefore, the system may not operate normally in6. INPUT switch @1starting to record.
Y Push the play button (The direction of playback isthe following cases :Y Select the recording source.
indicated (0 or 1)).Y Recordings with discontinuous speech or7. Rec/Rec mute (4) button @9
= When playback is finished, press the stop (2)conversation.Y When pressed, the tape deck goes into the
button @9.Y Recordings with long periods of pianissimorecord standby mode. The O4,3� will light. Initial
= To restart the tape, press the play (0 or 1) button(softly played music).setting of recording levels should be made in the
@9.Y Blank sections with a high level of noise.record standby mode.
Y Blank sections shorter than 4 seconds.8. INPUT LEVEL control @6
CAUTION :Y If noise-emitting appliances, such as electricY Used to set the recording level.
Y If different types of Dolby Noise Reduction arerazors, drills, refrigerators, etc., are operated
9. Play (0 or 1) button @9
used for record and playback, playback responsenearby.Y Recording starts when the play (0 or 1) button
will be adversely effected.Y REVIEW close to the beginning of the program or
@9 for the direction indicated by the lighting tape
CUE close to the ending.
travel indicator (0 or 1) is pressed. If the other
play (0 or 1) button @9 is pressed, the direction
of tape travel changes.
The play (0 or 1) and the O4� indicator will light
during recording.
= When recording is finished, press the stop (2)
button @9.
14 |
ACEC
DENON
