Digital outputSpeaker presence and size (a)
[DVD-A] [DVD-V]
1. Press [3, 4, 2, 1] to select the item and press [ENTER].
Change the settings when you have connected equipment through this
2. Press [3, 4] to select the setting and press [ENTER].
unitOs DIGITAL AUDIO OUT terminal (OPTICAL).
Icon examples:
LSLS
PCM Down ConversionSurround speaker (LS)
Select how to output audio with a sampling frequency of 96 kHz orNoLargeSmall
88.2 kHz.
eLarge: When the speaker supports low-frequency (under 100 Hz)
eSelect OYes� if the equipment you connect cannot process signals with a
reproduction.
sampling frequency of 96 kHz or 88.2 kHz.
eSmall: Select when the speaker does not support low-frequency
reproduction.
No (Factory preset): Output as 96 kHz or 88.2 kHz
Yes: Converted to 48 kHz or 44.1 kHz
If the subwoofer is set to No, the front speakers will automatically be set to
Large.
[Note]
Delay time (b)
eMake sure that ODigital Audio Output� setting (! page 21) is OOn�.
eSignals are converted to either 48 kHz or 44.1 kHz despite the above[DVD-V] (Dolby Digital and DTS, center and surround speakers only)
settings if the signals have a sampling frequency of over 96 kHz, or the
For optimum listening with 5.1-channel sound, all the speakers, except for
disc has copy protection.
the subwoofer, should be the same distance from the seating position. If
eSome equipment cannot handle sampling frequencies of 88.2 kHz, even
you have to place the center or surround speakers closer to the seating
if they can handle 96 kHz. Read your equipmentOs operating instructions
position, adjust the delay time to make up for the difference.
for details.
d Center speaker
Dolby Digital and DTS Digital SurroundDifferenceSetting
Approx. 50 cm (1 1/2 feet)1.3 ms
Bitstream (Factory preset for Dolby Digital):LCR
Select if the equipment you connected can decode the signal.Approx. 100 cm (3 feet)2.6 ms
d
eApprox. 150 cm (5 feet)3.9 ms
PCM (Factory preset for DTS Digital Surround):
Approx. 200 cm (6 feet)5.3 ms
Select if the equipment you connected cannot decode the signal.SW
f Surround speakers
f
DifferenceSetting
LSRSAdvanced operations
Approx. 200 cm (6 feet)5.3 ms
IMPORTANT
If the equipment you connected cannot decode the signal, theApprox. 400 cm (12 feet)10.6 ms
setting must be changed to PCM. If not, signals the equipment cannot
Approx. 600 cm (18 feet)15.9 ms
process will be output by this unit, causing high levels of noise which
can damage your hearing and the speakers.
If distances d (from the center speaker) and f (from the surround
speakers) are the same as or greater than e (from the front speakers),
leave the delay time as O0�, the factory preset.
Speaker settingIf either distance d or f is less than e, find the difference in the relevant
table and change to the recommended setting.
Change speaker presence and size a, delay time b, and channel balance
c to suit the speakers you have connected.Changing the delay time
These settings are not necessary when you select O2-channel� (only two1. Press [3, 4, 2, 1] to select the delay time box and press
speakers are connected).[ENTER].
[Note]2. Press [3, 4] to adjust the delay time and press [ENTER].
This feature works only for analog connection (! page 7).
Channel balance (c)
Front (L) CenterFront (R)
1. Press [3, 4, 2, 1] to select OTest� and press [ENTER].
ab a ca
A test signal is output from one speaker at a time, starting with the front
left speaker and proceeding clockwise.
SETUP
Front (L)_NN) Center_NN) Front (R)
ExitLm sCd BR:;
0 0
Surround (LS)(NNNNN== Surround (RS)
Exit
d BSW2. While listening to the test signal, press [3, 4] to adjust the
Test 0
volume of the center and surround speakers so they are the same
SELECT
apparent volume as the front speakers (j6 to i6).
d Bm sd BTestLSRS(The front speakers cannot be adjusted here.)
ENTER RETURN0 0 0
signal
3. Press [ENTER].
(LS) NN SurroundNN (RS)SubwooferThe test signal stops.
a c b c ac aeNo signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
To finish the speaker setting
Press [3, 4, 2, 1] to select OExit� and press [ENTER].
[Note]
The unit may be unable to output as set here due to limitations imposed by
RQT6263
the unit itself or the disc being played. (The displayOs OD.MIX� indicator
goes out in these cases.)
23 |
ACEC
PANASONIC
