Disc Type[3]FocusSearch the focus and turn on the focus.
1. Disc Type Auto Check
2. DVD SL12cm[4]TRKTurn ON/OFF the tracking servo.
3. DVD DL12cm
4. CD12cm[5]SledTurn ON/OFF the sled servo.
5. SACD12cm
If PLL is not locked (or can not be
6. DVD SL8cm
7. DVD DL8cmlocked), the sled servo does not be
turned ON. (Indication remains as OFF)
8. CD8cm
9. LCD8cm
0. Reset SLED TILT[6]CLVATurn ON/OFF normal servo of spindle
TC. --:--:-- EMG.00servo.
CD12cm
[7]FCS. SrchAppsame vly oltage as that of focus
Display when CD 12cm disc was selectedsearch to the focus drive to check the
focus drive system.
[0]Reset SLED TILTReset the Sled and Tilt to initial
position.(This model does not ha? veSled FWD TiltMove the sled outward. Perform this
device, so reset only the Sled to initialoperation with the tracking servo turned
position.)off.
[1]Disc Type CheckJudge automatically the loaded disc. ? Sled REVAsMove the sled inward. Perform this op-
the judged result is displayed at the bot-eration with the tracking servo turned
tom of screen, make sure that it is cor-off.
rect.
If Disc Check Memory menu has not
3. Track/Layer Jump
been executed after EEPROM default
setting, the disc type cannot be judged.Tracking/Layer Jump
In this case, return to the initial menu1. 1Tj FWDR. Fj (L1 ? L0)
and make a check for three types of2. 1Tj REVL. Fj (L0 ? L1)
discs (SL, DL, CD).3. 2Tj FWDU. Lj (L1 ? L0)
4. 2Tj REVD. Lj (L0 ? L1)
5. NTj FWD
[2] to [9]Select the loaded disc. The adjusted
6. NTj REV
value is written to the address of se-7. 500Tj FWD
lected disc. No further entry is neces-
8. 500Tj REV
sary if [1] was selected.9. 10k/20k FWD
0. 10k/20k REV
2. Servo ControlSA.------ SI.-- EMG. 00
DVD SL 12 cm
Servo Control
1. LDOff R. Sled FWDOn this screen, track jump, etc. can be performed. Only for the
2. SPOff L. Sled REVDVD-DL, the focus jump and layer jump are displayed in the right
3. FocusOfffield.
4. TRK.Off
5. SledOff
[1]1Tj FWD1-track jump forward.
6. CLVAOff
7. FCS. Srch Off
[2]1Tj REV1-track jump reverse.
0. Reset SLED TILT[3]2Tj FWD2-track jump forward.
SA.------ SI.-- EMG. 00
DVD SL 12 cm[4]2Tj REV2-track jump reverse.
On this screen, the servo on/off control necessary f[5] NTj FWDor replay isN-track jump forward.
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes acti[6] NTj REVve. InN-track jump reverse.
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not loc[7] k500Tj FWDed.Fine search forward.
The spindle could run overriding the control if the spindle system
is faulty or RF is not present. In such a case, do not oper[8] 500Tj REVate CLVA.Fine search reverse.
[0]Reset SLED TILTReset the Sled and Tilt to initial[9]10k/20k FWDDirect search forward.
position.(This model does not have Tilt
device, so reset only the Sled to initial[0]10k/20k REVDirect search reverse.
position.)
� The following commands are valid for DVD-DL disc only �
[1]LDTurn ON/OFF the laser.
? Fj (L1 ? L0)Focus jump forward.
[2]SPTurn ON/OFF the spindle.(Trk/Sled Servo OFF)
6-9 |
ACEC
SONY
