DVR-6300
CONTENTS / ACCESSORIES / CAUTIONS
CONTENTS
CONTENTS / ACCESSORIES / CAUTIONS...............2EXPLODED VIEW .....................................................25
PARTS DESCRIPTIONS .............................................3PARTS LIST...............................................................27
PC BOARD ..................................................................4SPECIFICATIONS .....................................................34
SCHEMATIC DIAGRAM ............................................15
ACCESSORIES
FM indoor antenna (1)Loop antenna (1)Accessories for speaker part
(T90-0917-08)(For Europe)(For U.S.A., Canada (For DVT-6300 and DVT-7300)
(T90-0916-08) and Australia)Speaker cords (6) *
(T90-0915-08)
Length
For Front (2)4.5 m (177-3/16")
For Center (1)3 m (118-1/8")
For Rear (2)8 m (314-15/16")
For Subwoofer (1) 4.5 m (177-3/16")
Video cord (Yellow)(1)Remote control unit (1)Batteries
(E30-7341-08)(A70-1685-08)(R03/AAA) (2)
Cushion (15) *
(Small : 11 pcs 1 sheet) (Big : 4 pcs 1 sheet)
* See speakerOs manual.
SYSTEM CONFIGURATIONS
SYSTEMRECEIVERSPEAKERSPEAKER
DVT-6300-HDVR-6300KSW-6300-H-
DVT-6300-SDVR-6300KSW-6300-S-
DVT-7300DVR-6300KSW-7300-
DVT-8300DVR-6300KS-908HTSW-18HT
CAUTIONS
Operation to resetNote related to transportation and movement
The microprocessor may fall into malfunction Before transporting or moving this unit, carry out the
(impossibility to operate erroneous display, etc.) following operations.
when the power cord is unplugged while power is
ON or due to an external factor.1. Set the POWER ON/OFF switch to the ON
In this case, switch off the power, wait for several without loading a disc.
seconds, and then switch the power on again.2. Wait a few seconds and verify that the display
shown appears.
For the U.S.A.
"NO DISC"
CAUTION:
Use of controls or adjustments or performance of procedures3. Set the POWER ON/OFF switch to OFF.
other than those specified herein may result in hazardous radia-
tion exposure.
In compliance with Federal Regulations, the following are repro-
ductions of labels on, or inside the product relating to laser prod-Caution on condensation
uct safety.
Condensation (of dew) may occur inside the unit when there is a great
KENWOOD CORPORATIONdifference in temperature between this unit and the outside. This unit
2967-3, ISHIKAWA-CHO,may not function properly if condensation occurs. In this case, leave
HACHIOJI-SHI,the unit for a few hours and restart the operation after the condensa-
TOKYO, JAPANtion has dried up.
KENWOOD CORP. CERTIFIES THIS EQUIPMENTBe specially cautious against condensation in the following circum-
CONFORMS TO DHHS REGULATIONS NO. 21 CFRstances:
1040.10, CHAPTER 1, SUBCHAPTER J.When this unit is carried from one place to another across a large
difference in temperature, when the humidity in the room where
Location: Back Panelthis unit is installed increases, etc.
For the U.S.A.
Note to CATV system installerThe marking of products using lasers
This reminder is provided to call the CATV system installer?s at-(For countries other than U.S.A. and Canada)
tention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-CLASS 1
ing, as close to the point of cable entry as practical.LASER PRODUCT
For CanadaThe marking this product has been classified as Class 1. It
means that there is no danger of hazardous radiation outside
NOTICE: This Class B digital apparatus complies withthe product.
Canadian ICES-003.Location: Back panel
2 |
ACEC
KENWOOD
