When Master Cue is pressed only the master holding it in position. Replace the fader with
output is heard. a quality authorized replacement from your
16. ?Headphone Jack? (Quarter Inch Output local Numark retailer.
Terminal): Your headphones can be 18. ?Contour Knob? (Crossfader Rate/Slope
connected to this 1? terminals. The Control): The position of this switch
Volume should always be set at its lowest determines how quickly or intensely the
setting while connecting and disconnecting crossfader will act depending upon mode
headphones to prevent damage to setting.
headphones and/or your hearing. 19. ?Direction Button? (Crossfader Reverse
Control): Activation of this switch reverses
Crossfader Controls the assignment of CH-1 and CH-2 on the
17. ?Crossfader Slider? (Digital VCA Crossfader): crossfader.
This slide fader blends audio between CH-1 Output Controls
and CH-2. Its action can be modified with 20. ?Master Knob? (Main Output Level Control):
the ?Mode? , ?Slope?, and ?Direction? This rotary control adjusts the main output
controls. This digital mixer uses digital VCA volume.
technology to accurately determine slider
position. Both the VCA and Digital 21. ?Booth Knob? (Master/Split Style Headphone
technologies combined allow for some very Cueing Switch): This rotary control adjusts
powerful effects. the auxiliary (AKA booth) output volume.
Note: This fader is user replaceable if it
should ever wear out. Simply remove the
facepanel and then remove the screws
REAR PANEL FEATURES
1. ?AUX-SESSION INPUT? (Auxiliary Input): The line level input is used to connect the output from an external
mixers or additional CD players and other line level devices such as samplers, tape decks, keyboards, and line
output turntables. This input is mixed with any connected microphone.
2. ?Phono/AUX Inputs? (Turntable Input Connection): The Phono input is used for connecting your turntables or
other devices. Input source is determined by the PHONO/LINE switch on the rear panel.
3. ?Phono/Line source switch?: This switch activates and deactivates the sensitive RIAA phono preamplifiers. Only
turntables with phono level output should be assigned when the switch is in the phono position. Some
turntables offer line level output. To use these turntables and other line devices like CD players, switch the
input to Line.
4. ?GND? (Grounding Lug): This screw connector should be used to secure any devices connected to the mixer
that need to be grounded. Many turntables that are connected to the mixer will need to have a ground wire
that is designed to connect to the mixer?s chassis to eliminate hum and excessive noise.
5. ?Line Inputs? (CD player, Tape Deck, Sampler Input Connection): The line level input is used to connect CD
players and other line level devices such as samplers, tape decks, keyboards, and line output turntables.
6. ?Booth Output? (Auxiliary Stereo Unbalanced Output): This RCA output is for connecting a secondary external
monitoring device such as a booth monitor or second stereo output. The level of the booth output signal will
increase as the ?Booth? volume control is I ncreased.
7. ?Master Unbalanced Output? (Main Stereo RCA Output): This RCA output is for connecting an external
monitoring device such as a PA system, powered monitors or a home stereo. The level of the master stereo
output signal increases as the ?master? volume control is increased.
8. ?Master Balance Output? (Balanced Quarter Inch Stereo Output): These 1? outputs are for sending a balanced
level signal to a PA system or recording device. The level of the balanced output signal will also increase with
the ?master? volume control. These outputs are durable, offer a better output signal, and are well suited for
long cable runs.
9. ?Digital Output? (Optical): 48kHz, 24-bit S/PDIF output. The format is type 2, form 1, also known as S/PDIF
(Sony/Phillips Digital Interface Format). This output can be connected to compatible devices such as CD
Burners, Hard Drive recorders, or other digital mixers. Higher audio fidelity is maintained from these outputs.
10. ?Digital Output? (Coax): 48kHz, 24-bit S/PDIF output. The format is type 2, form 1, also known as S/PDIF
(Sony/Phillips Digital Interface Format). This output can be connected to compatible devices such as CD
Burners, Hard Drive recorders, or other digital mixers.
11. AC In: This mixer is designed to work with the power supply assembly that comes with the unit. While the
power is switched off, plug the power supply into the mixer first, then plug it into the outlet.
12. Power Switch: Use this switch to turn on the mixer after all input devices are already connected to prevent
damage to your equipment. Turn the mixer on before you turn on amplifiers and turn of amplifiers before you
turn off the mixer |
ACEC
NUMARK
