1 - 10Allgemeiner Teil / General Section
EXPERT control levelEXPERT control level
Possible settings 1�§W3Security LED (on/off)6Autom. change of regional programme9MCD and AUX input sensitivity§QClock synchronization
�BLK ON� The Security LED flashes if If an RDS programme consists of variousto adjust the sensitivity to a CD changer.�sync ON� The built-in clock is
1Activating coding (for details, see thethe radio andthe ignition areregional programmes, it may occur that�MCD LOW� lowsynchronized by RDS
chapter �Coding�, page 16).switched off.your car radio changes between regional�MCD MID� medium signals.
If �CODE� appears in the display, coding is�BLK OFF� The Security LED does notstations when changing the reception area.(eg. MCD 36/MCD 40)�sync OFF� In areas where no RDS
not activated.flash.�MCD HIGH� highTIMER signals are received,
�REG ON� autom. change of regional
If �SAFE� appears in the display, coding isprogramme is possible.the synchronization func-
activated.4Sound signal (on/off)�REG OFF� nochange of regional §IVolume limitation when switching ontion can be deactivated.
�BEEP ON� Sound signal as function con-programme is possible.�ONVOL - -�: no limitation
2Display brigthnessfirmation.�ONVOL 20�: max. volume, eg., 20 §WDIGITIME
�DISPL 07� (00 � 07). Set according to the�BEEP OFF� Function confirmation7Switching on and off with the (- - � 46). �TM 00:00� This function serves for
location of the car radio so thatthrough brief muting of theignition/start switchThe volume is limited only if the volumemanual time setting. If you
the display can optimally be readloudspeaker outputs.�IGN ON� It is possible to switch the radiowhen the car radio is switched off is turn the right-hand control
off.on and off with the ignition/startgreater than the set value!knob quickly, it will act as a
66If you havec connected the car radio to 5Autom. LEARN (radio mode)switch of the vehicle.§?Minimum volume for traffic flywheel.
the illumination contact of the vehicleOsIf you are in a reception area in which�IGN OFF� Switching on and off is only 66If �sync ON� has been selected (see §Q),
announcements
plug connector, the display brightness willreception of RDS programmes with trafficpossible with the �IO button.the manually set time may be corrected
change if the headlights of the vehicle areannouncements is poor, you can disable�TA VOL 16� (5 � 46)by the currently received RDS station.
switched on (night setting) or off (day the autom. LEARN function in radio mode.8Muting in telephone modeThe volume for the traffic announcementIf this RDS station should transmit an
setting). Both settings can separately be�PHONE ON� Muting activated.can be heard during setting.undesired time, you must disable this
selected and stored in memory with �LRN ON�: autom. LEARN correction by selecting �sync OFF�.
switched on or switched off headlights.�LRN OFF�: no autom. LEARN wished.�PHONE OFF� Muting deactivated.§`CLOCK ON/OFF
�CLOCK ON� Time indication on.
66If the volume is set below �VOL 4�, the�CLOCK OFF� Time indication off.
�LRN ON� setting is supposed.
CodingCoding
Activating the codingDeactivating codingReturn to operationThe table shows the waiting periods betweenWaiting periods
66Your personal code number is on the iden-the individual attempts.
tity card of your car radio.1.Select the EXPERT control level and turnbefore removing the car radio, for example.With coding activated, the car radio is electro-To prevent deactivation of the coding beingWaiting period after the 7th attempt is always
the right-hand cccontrol knob until �CODE�Coding is not activated when the radio lea-nically disabled after it has been disconnectedpossible by trial and error, waiting periods are24 hrs!
ves the factory.1.The EXPERT mode must be switched onappears in the display.from the car battery (or permanent plus, ter-required between attempts. During these wait-After the 6th attempt we recommend having a
and �SAFE� indicated in the display.
If you have Oactivated� your car radio'sActivate the change mode:Activate the change mode:minal 30), e.g. after the radio has been remo-ing periods, the car radio can be switched ondealer complete the OReturn to operation� or
coding: As soon as you disconnect the carBriefly press the right-hand cccontrolBriefly press the right-hand cccontrolved during servicing.and off but will not play.ODeactivate coding� process.
radio from the car battery (or permanentknob. The display indicates �CH- - - -� knob. The display indicates �CH1- - - -� 1.Switch on the car radio.During the waiting period
plus terminal 30), it is electronically(CH = Change).(CH = Change).The display indicates �SAFE�.the car radio needs not be switched on, but
2.Enter the code number (on the Identityblocked. After approx. 3 seconds, the display indi-it must be connected to the permanent +12 VAttemptWait.per.
Only you are able to put it back into opera-2.Enter the code number (on the IdentityCard): Use the right-hand cccontrol knobcates �I- - - -�. (The �I� stands for thevoltage. As long as the display indicates(in display) (approx.)
tion by entering your personal Code Number.Card) by turning the right-hand cccontrolto enter the correct number.number of attempts)."SAFE", the waiting period has not yet elapsed.
knob as described under �Activating121 sec.
The waiting period is over when the number
2
Is the coding activated?66When the right-hand cccontrol knob is Coding� 2.Enter the code number (on Identity Card),of the next attempt is visible in the display,1.5 min.
turned quickly, it will function like aby turning the right-hand cccontrol knob 35.5 min.
3.Confirm the code number:e.g. "2- - - -".4
Activate the EXPERTmode and turn the flywheel.as described in the chapter �Activating22 min.
Press the right-hand cccontrol knob until5
left-hand cccontrol knob until the display indi-coding�.1.5 hrs.
3.Confirm the code number:�CODE� appears briefly in the display.6
cates "SAFE" or "CODE".6.0 hrs.
Briefly press the right-hand cccontrol knob.The radio will play after approximately 3.Confirm the code number:7
�SAFE� appears in the display.3 seconds.Press the right-hand cccontrol knob until24 hrs.8
Coding is activated!�SAFE� appears briefly in the display.24 hrs.
Coding is deactivated!
4.Deactivate the EXPERT control level:After approximately 3 seconds the radio
If you have entered the incorrect code
Press the � button or the right-handwill play.
GRUNDIGServiceCoding activated.number:
cccontrol knob until the sig-
"SAFE" remains in the display and the radioIf you have entered the incorrect code
nal sounds.does not play.number:
"SAFE" remains in the display and the radio
Begin again. Be sure to observe the waitingEC 4790 CD
does not play.
periods between attempts (see page 17).
Begin again. Be sure to observe the waiting
Coding not activated.periods between attempts. |
ACEC
GRUNDIG
