1 &3$
�?´
This Beard/Hair Trimmer is for theE Trimming Length IndicatorK Blade BlockThe charge status lamp will glow
trimming and care of mustaches,Release to remove the bladewhen the trimmer is being charged.
IndicatorTrimming Length
beards and hair. Trimming length canblock from the housing to cleanIt will flash when the charging is com-
be adjusted between 1 to 20 mm. The11.0 mmor replace the blade. (see fig. 12)pleted. (see fig. 4)
trimmer can be operated either from22.0 mmYou can fully charge the trimmer in 1
L Finishing blade of Mini Trimmer
an AC power source or on its ownhour if it seems to be losing speed.
�3.5 mmUse this when finishing the edges
rechargeable battery.A full charge will supply enough
(see fig. 8) and trimming the
55.0 mmpower for approx. 10 trims (5 minutes
moustache.
�6.5 mmper trim for a normal beard).
Parts identificationM Trimmer guide of Mini Trimmer
88.0 mmSlide it up when finishing blade is
(see fig. 1)
�9.5 mmused.AC operation
A Switch
1111.0 mmN AdaptorConnect the AC adaptor to the bodySlide up to turn on, slide down to
Use this to connect the trimmerin the same way as for charging, andturn off.�12.5 mm
to an AC power source for re-set the switch to �1� to use the trim-
B Charge Status Lamp1414.0 mmcharging or for AC operation.mer.
Lights when the unit is connected
�15.5 mmO OilIf the trimmer does not operate after
with the adaptor N to an AC
connection as mentioned above, re-
1717.0 mmLubricate the space between thepower source for charging.
turn switch to �0�charge� position for
stationary and moving blade with
C Main Blade2 or 3 drops of oil after use. (see�18.5 mm1 minute and then set switch back to
A precision 39 mm-wide blade2020.0 mm�1� position.
fig. 16)
which can be used with the comb
P Cleaning Brush
attachment FG.
� The actual hair length may be
Trimming of beard
longer than the set trimming hight.READ ALL INSTRUCTIONS BE-D Quick Adjust Dial
Place the angled face of the comb
Turn the dial to a higher setting to
F Comb Attachment for BeardFORE USE.against the skin and cut the beard
raise or lower the comb attach-
Type that restricts cut hair scat-
by moving the trimmer in all direc-
ment FG to the desired length
tering.tions to obtain a uniform cut. (see fig.
(between 1 and 20 mm) (see fig.Operation
Use this to control the trimming
5)
2). The comb attachment is locked
length. (see fig. 3)With curly facial hair, the comb at-
in position when the switch is setCharging and cordless trimming
G Comb Attachment for HairWhen charging the beard/hair trim-tachment may not cut all of the hair.
to �1�.
Use this to control the trimmingmer for the first time or when it hasIn this case, remove the comb attach-
length. (see fig. 3)not been in use for more than 6ment and use a conventional comb
months, charge it for the activationto draw out the remaining uncut, hair.
H Moving Blade
for at least 16 hours before use.(see fig. 6)
I Stationary BladeConnect the power cord to the beard/When shaping the beard, remove the
J Cleaning Leverhair trimmer, and plug the adaptor tocomb attachment. Place the angled
Push this lever to remove bits ofan AC outlet.edge against the skin and make the
hair caught between the station-In some areas, a special plug adap-border of the beard even.
ary blade and the moving blade.tor may be required.
56
67 |
ACEC
PANASONIC
