HOLD FM TUNER
Switching radio on/off
Y To deactivate HOLD, switch the slider to OFF.
YPress FM to switch the radio on.
� All the buttons are unlocked.
� Display shows briefly followed by
waveband (FM), fre-
Helpful Hint:
quency and preset number (01-30) if already
� If you deactivate HOLD by switching the slider on the set to RESUME, you willstored.
be activating the RESUME function.YTo switch the radio off, press FM again (or press 9).
� Display shows.
ACOUSTIC FEEDBACK (BEEP)
Tuning to stations: Use the remote control or set
Acoustic feedback is a beep signal that is heard when buttons on the set orto tune to any FM station automatically or manually
remote control are pressed. Also, when the set or remote control is in pause1Press and hold SEARCH or §until the frequency
mode or the battery power is low, it beeps at intervals.in the display starts running.
1Keep DBBpressed for more than 2 seconds to switch the beep either off or� The radio automatically tunes to a station of sufficient reception.
on.Display showsduring automatic tuning.
�: Beep is switched off.
2Repeat searching until you find the desired radio station.
YTo tune to a weak station, press or § briefly and repeatedly
�: Beep is switched on.
until you have found optimal reception.
Helpful Hint:
Helpful Hint:
� Beep is on as the default setting.
� To improve reception: The headphone wire is used as an FM antenna.
If necessary, move it for optimum reception.
� Tuner operation is not affected if you open the CD lid to change a disc.
� FM Tuner: DBB is always off.
FM TUNERTROUBLESHOOTING
Programming radio stations (remote control only)WARNING: Under no circumstances should you try to repair the unit yourself as
You can store up to 30 radio stations.this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
1Tune to a desired radio station. (see Tuning to sta-
these hints, consult your dealer or service center.
tions)
2Press PROG to activate programming. The CD player has no power, or playback does not start
� Preset number (up to 30) flashes, indicating theY Check that your batteries are not dead or empty, that they are inserted
next program location available.correctly, that the contact pins are clean.
� If necessary, press ALBUM + / - to select a pre-YYour adapter connection may be loose. Connect it securely.
set number.
The indicationis displayed
3Press PROG again to confirm.
Y Check that the CD is clean and correctly inserted (label-side upward).
� Display shows: the preset number and frequency
Y If your lens has steamed up, wait a few minutes for this to clear.of the preset station.
Y Make sure the CD is not encoded with Copyright protection technologies,
4Repeat steps 1-3 to store other stations.
as some do not conform to the Compact Disc standard.
The indicationis displayed
Tuning to a preset radio station
Y CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.Y Press ALBUM + / - once or more until the desired
preset station is displayed.The indicationis displayed
Y CD contains non-audio files. Insert a suitable disc or press SEARCH / §
Clearing a preset once or more to skip to an audio track, instead of the data file.
Y During playing a preset, press and hold PROG 2 seconds.
The indicationis on and/or there is no reaction to controls
Y If HOLD is activated, then deactivate it.
Helpful Hint:Y Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
� Already stored stations can be recognized by a preset number.The indicationis displayed and the track cannot be played
� You can erase a preset station by storing another frequency in its place.Y The wma file is protected by WM DRM (Windows Media Digital Rights
Management). Use Windows Media Player 10 (or later) for CD burning/conver-
sion. |
ACEC
PHILIPS
