SONY FDL-3500 Instruction Manual

$4.99

SONY FDL-3500 - It's a complete owner's manual ( also known as operating manual or user guide), and it's in PDF format. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

oleg volkozub - 09/25/2008

Very nice clear manual with specifications, thanks!

Nadia Yakunina - 06/19/2007

It was so difficult to find this manual on the internet - thanks a lot for making it so easy and simple. Incredibly handy. AND. It looks you make so many people happy for such small money. Good job!

James Thorp - 12/28/2006

Great original Yamaha manual and no problems at all with the ordering process. Will definitely use this website again and would recommend it to anyone else. James Thorp

francesco mayol - 02/11/2007

This is the best site to find what you need.I reccomand all thecnicia n to contact User-Manuals .

Othmar Herbst - 01/13/2008

PDF contains : - schematics, but a little un-sharp. - disassembly instructions, accurate drawings - description of test-modes

Customers who bought this product also purchased

SONY 17VC Owner's Manual	SONY 14DK1 Service Manual	SONY AC-E45A Owner's Manual
SONY 16229172 Service Manual	SONY AC-E15A Owner's Manual	SONY AC-E30A Owner's Manual

Click to see text excerpt from the manual

1FDL- 3500
SECTION 3
ELECTRICAL ADJUSTMENTS
3- 1. TV SECTIONWAVEFORM CHECK
PRECAUTIONProcedure :
1.Make adjustment in sequence as described.1. Y. signal check (H cycle)
2.Power supply voltage is + 9.0 t O.lV (DC jack end)Input the color bar signal from A/V IN jack (J201).
unless otherwise specified. Power supply shall not beConnect an oscilloscope to TP (Y) to check if the
input overlapped.waveform is as shown in the following figure.
3.Check the error in waveform and screen for adjustment.
White
4.Measure a fluorescent tube and an liquid crystal display---I-(100%)
0.5*o.lvP-P
module device by connecting them with the main board.
-.I.-
5.Unless otherwise specified, input the color bar signal,
etc. from A/V IN jack (J201) by using AV-cord (AVK-
715M, etc.) to intercept the internal TV detection2. Synchro signal check (H cycle)
output.Connect an oscilloscope to TP (SYNC) to check if the
Also, usually use monochromatic gradation wave monowaveform is as shown in the following figure.
scope with chroma signal and burst signal OFF.
--I-
6.Measuring instruments
0.8&O. 1 SVp-p
l NTSC pattern generatorc
t--H-+ -
Il Digital multitester
l Oscilloscope
7.Modes of Switches and Volume3. Color burst signal check (H cycle)
S601 (POWER) . . . . . . . . . . . . . . . . .ONConnect an oscilloscope to Pin @ of IC300 (CHROMA)
S2 (TV BAND) . . . . . . . . . . . . . . . . . ONto check if the waveform is as shown in the following
S18 (VOL -). . . . . . . . . . . . . . . . . ..minimumfigure.
VOLTAGE ADJUSTMENT
Procedure :
1. Connect a digital multitester between TP (+ 5V) andk-----dchroma signal
1
(GND) on the main board, and then adjust RV602 socolor burst signal
that the reading of the voltage is + 4.8 + 0.05V.4. H pulse check (H cycle)
Connect a digital multitester between TP (+ 9V) andConnect an oscilloscope to Pin @ of IC300 (H PULSE)
(GND) and then adjust RV601 so that the reading ofto check if the waveform is as shown in the following
the voltage is + 9 + O.lV.figure.
(+4. SVDC)
Connect a digital multitester between TP (+ 7V) and
--r-
(GND) and then adjust RV701 so that the reading of
3,0k0,4VP-P
the voltage is 6.7 + O.lV.(+secl----
wcLJb
(about 63.5pec)
Adjustment Location: INVERTER BOARD
5. Common signal check (2H cycle)
Connect an oscilloscope to TP (COM) to checkif the
waveform is as shown in the following figure.
V
(63.5psec)
- -
5