UX-A450DE/IT/H
NX-A550DE/IT/FO-A650IT
SW-A5 No. 5, No. 6 Digital cable equalizer settingSW-B2 No. 7, No. 8 Reserved
(Reception for Caller ID)
Set to "0".
Line equalization when reception for CALLER ID is to be set according
SW-B3 No. 1 ~ No. 5 Reserved
to the line characteristics.
Setting should be made according to distance between the telephoneSet to "0".
and the telephone company central switching station.
SW-B3 No. 6, No. 7 Auto dial mode Delay timer of before line con-
SW-A5 No. 7 Error criterionnect
Used to select error criterion for sending back RTN when receiving im-Delay time between the dial key input and line connection under the
age data.auto dial mode.
RAPID01CML RELAY ON
SW-A5 No. 8 Anti junk fax check
When using the Anti junk fax function, set to "1".
DIALLING
SW-A6 No. 1 Reserved
No.6 No.7
Set to "0".
0 0 0sec
0 1 1.5sec
SW-A6 No. 2 End buzzer
1 0 3.0sec
Setting this bit to 0 will disable the end buzzer (including the error buzzer/1 1 4.5sec
on-hook buzzer).
SW-B3 No. 8 Reserved
SW-A6 No. 3 Disconnect the line when DIS is received in RX modeSet to "0".
Bit1= 0: When DIS signal is received during RX mode, the line is discon-
SW-B4 No. 1, No. 2 Auto dial mode Delay timer of after line connect
nected immediately.
Delay time between the line connection and dial data output under the
Bit1= 1: When DIS signal is received during RX mode, the line is discon-auto dial mode.
nected on the next tone.DIAL DATA
RAPID01CML RELAY ON
SW-A6 No. 4 Equalizer freeze control (MODEM)
This switch is used to perform reception operation by fixing the equal-
izer control of modem for the line which is always in an unfavorable
No.1 No.2
state and picture cannot be received.
0 0 1.7sec
* Usually, the control is executed according to the state of line where0 1 3.0sec
the equalizer setting is changed always.1 0 3.6sec
1 1 4.0sec
SW-A6 No. 5 Equalizer freeze control 7200BPS only
SW-B4 No. 3 Dial mode
Setting which specifies SW-A3 No. 6 control only in the condition ofWhen using the pulse dial, set to 1. When using the tone dial, set to 0.
7200BPS modem speed.
SW-B4 No. 4 Pulse ? Tone change function by key
SW-A6 No. 6 CNG transmission in manual TX mode
When setting to 1, the mode is changed by pressing the key from the
When set to "1", fax transmit the CNG signal in case of manual trans-
pulse dial mode to the tone dial mode.
mission mode (User press the START key after waiting for the fax an-
swering signal from handset or speaker).SW-B4 No. 5 Dial pulse make/break ratio (%)
When using the 33% make ratio pulse dial, set to "0".
SW-A6 No. 7 Reserved
When using the 40% make ratio pulse dial, set to "1".
Set to "0".
SW-B4 No. 6, No. 7 Reserved
SW-A6 No. 8 Modem speed automatic fallback when RX level is
Set to "0".
under -40dBm
When set to "1", if fax signal level is under -40dBm during reception,SW-B4 No. 8 Recalling fixed only one time when dialing was un-
machine selects the slower modem speed automatically.successful without detecting busy tone signal
It is effective when noises occur on the received document due to theWhen dialing results in failure since the busy tone cannot be detected,
long distance communications.recalling is fixed to one time.
SW-B1 No. 1 ~ No. 4 Recall intervalSupplementary explanation
If time-out termination is made when dialing, only single recall is possi-
Choice is made for a redial interval for speed and rapid dial calls.
ble even if the setting time of recalls (SW-B1 No. 5 - No. 8) has been set
Use a binary number to program this. If set to 0 accidentally, 1 will be
to some times. This soft switch is added in order to meet FCC.
assumed.
SW-B5 No. 1 ~ No. 5 DTMF signal transmission level (Low)
SW-B1 No. 5 ~ No. 8 Recall times
The transmission level of DTMF signal is adjusted. (lower frequency)
Choice is made as to how many redials there should be.
00000: 0dBm
SW-B2 No. 1 Dialing pause (sec/pause)
?
Pauses can be inserted between telephone numbers of direct dial con-
nection. Selection of 4 sec or 2 sec pause is available.11111: -15.5dBm (-0.5dBm x 31)
SW-B2 No. 2 Dial tone detection (before auto dial)SW-B5 No. 6 Dial pulse format
Used to set YES/NO of dial tone detection in auto dialing.If this switch is set to O1�, pulse dial number dials +1.
(Example)
SW-B2 No. 3 Reserved
0: dial 1
Set to "0".9: dial 0 (10 pulses)
SW-B2 No. 4 Busy tone detection (after auto dial)SW-B5 No. 7 Flash send time
Used to set busy tone detection in auto dialing.Used to select length of Flash.
No. 7=0: 90msec (Short time)
SW-B2 No. 5, No. 6 Waiting time after dialing
No. 7=1: 250msec (Long time)
This is time waiting for the opponentOs signals after dialing.
2 � 15 |
ACEC
SHARP
