Operation Guide 3751
World Time3. When the setting you want to change is flashing, use B and D to change it as
described below.
World Time digitally displays the current time in 27 cities
City code (29 time zones) around the world.SettingScreenButton Operation
" All of the operations in this section are performed in the WorldStart TimeUse D (+) and B (�) to change the setting.
Time Mode, which you enter by pressing C." You can set a start time in the range of 1 to 60 minutes in
1-minute increments.
To view the time in another cityAuto-repeatPress D to toggle auto-repeat on ( displayed) and off
In the World Time Mode, press D to scroll eastwardly( displayed).
through city codes.Progress BeeperPress D to toggle the progress beeper on (ON) and off
" The city code is displayed for about one second, and then(OF).
it is replaced with the current time for that city code.
" For full information about city codes, see the OCity Code4. Press A to exit the setting screen.
Current time for the Table�." You can also perform steps 1 and 2 of the above procedure whenever you need to
selected city code " If the current time shown for a city is wrong, it probably
view the current auto-repeat and progress beeper settings.
means there is a problem with your Timekeeping Mode
time and/or Home City code settings. Go to theTo use the countdown timer
Timekeeping Mode and make the necessaryPress D while in the Countdown Timer Mode to start the
adjustments.countdown timer.
" The countdown timer operation continues even if you
To toggle a city code time between Standard Time and Daylight Saving Timeexit the Countdown Timer Mode.
1.In the World Time Mode, use D to display the city code" Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
whose Standard Time/Daylight Saving Time setting you
want to change." To completely stop a countdown operation, first pause it
2.Hold down A for about two seconds to toggle between(by pressing D), and then press A. This returns the
countdown time to its starting value.
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
" The DST indicator is on the display whenever you
DST indicator display a city code for which Daylight Saving Time isStopwatch
turned on.
" Note that the DST/Standard Time setting affects only theThe stopwatch lets you measure elapsed time, split times,
currently displayed city code. Other city codes are notand two finishes.
affected." The display range of the stopwatch is 59 minutes,
" Note that you cannot switch between Standard Time59.99 seconds.
and Daylight Saving Time while GMT is selected as the" The stopwatch continues to run, restarting from zero
city code.after it reaches its limit, until you stop it.
" The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Countdown TimerMinutes " Exiting the Stopwatch Mode while a split time is frozenon the display clears the split time and returns to
The countdown timer can be set within a range of one1/100 Seconds elapsed time measurement.
minute to 60 minutes. An alarm sounds when thesecond " All of the operations in this section are performed in the
countdown reaches zero. The countdown timer also hasStopwatch Mode, which you enter by pressing C.
an auto-repeat feature and a progress beeper that signals
the progress of the countdown.To measure times with the stopwatch
" All of the operations in this section are performed in the
Elapsed Time
Countdown Timer Mode, which you enter by pressing
C.
StartStopRe-startStopClear
Minutes
Configuring the Countdown Timer
Seconds The following are the settings you should configure beforeSplit Time
actually using the countdown timer.
Countdown start time; Auto-repeat on/off; ProgressStartSplitSplit releaseStopClear
beeper on/off
" See OTo configure the countdown timer� for informationTwo Finishes
about setting up the timer.
Auto-repeatStartSplitStopSplit releaseClear
When auto-repeat is turned on, the countdown automatically restarts from theFirst runner Second runner Display time of
finishes.finishes.second runner.
countdown start time when it reaches zero. If left running, the countdown is repeatedDisplay time of
a total of eight times, after which it stops automatically.first runner.
When auto-repeat is turned off, the countdown stops when it reaches zero and the
display shows the original countdown start time.
" Pressing D while an auto-repeat countdown is in progress pauses the current
countdown. You can resume the auto-repeat countdown by pressing D, or you canAlarms
press A to reset to the countdown time starting value.
You can set five independent Daily Alarms. When an
Countdown Timer Beeper OperationsAlarm number alarm is turned on, the alarm tone sounds when the alarm
The watch beeps at various times during a countdown so you can keep informedtime is reached. One of the alarms is a snooze alarm,
about the countdown status without looking at the display. The following describes thewhile the other four are one-time alarms.
types of beeper operations the watch performs during a countdown.You can turn on an Hourly Time Signal that causes the
Countdown End Beeperwatch to beep twice every hour on the hour.
The countdown end beeper lets you know when the countdown reaches zero." There are six screens in the Alarm Mode. Four are for
" When the progress beeper is turned off, the countdown end beeper sounds forone-time alarms (indicated by numbers from
about 10 seconds, or until you press any button to stop it.AL1through AL4), one is for a snooze alarm
" When the progress beeper is turned on, the countdown end beeper sounds for(indicated by SNZ), and one is for the Hourly Time
about one second.On/Off status Signal (indicated by SIG).
" All of the operations in this section are performed in the
Progress BeeperAlarm time Alarm Mode, which you enter by pressing C.
When the progress beeper is turned on, the watch uses beeps to signal countdown(Hour : Minutes)
progress as described below.
" Starting from five minutes before the end of the countdown, the watch emits fourTo set an alarm time
short beeps at the top of each countdown minute.1.In the Alarm Mode, use D to scroll through the alarm
" 30 seconds before the end of the countdown, the watch emits four short beeps.screens until the one whose time you want to set is
" The watch emits a short beep for each of the last 10 seconds of the countdown.displayed.
" If the countdown start time is six minutes or greater, the watch emits a short beep for
each second of the final 10 seconds before the five-minute point is reached. Four
short beeps are emitted to signal when the five-minute point is reached.
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current" To set a one-time alarm, display one of the screens indicated by an alarm number
countdown start time starts to flash, which indicates thefrom AL1through AL4. To set the snooze alarm, display the screen indicated
setting screen.by SNZ.
" If the countdown start time is not displayed, use the" The snooze alarm repeats every five minutes.
procedure under OTo use the countdown timer� to2. After you select an alarm, hold down A until the hour setting of the alarm time
display it.starts to flash, which indicates the setting screen.
2. Press C to move the flashing in the sequence shown" This operation automatically turns on the alarm.
below to select other settings.3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (�) to change it.
Start TimeAuto-repeat" When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
Progress Beeper5. Press A to exit the setting screen.
2 |
ACEC
CASIO
