ENGLISH
General description.If you do not know what kind or kinds of fabric an article is made of, determine the
right ironing temperature by ironing a part that will not be visible when you wear or
A Spray nozzle (GC1830/1820/1815/1720/1705)
B Filling openinguse the article.
C Steam controlSilk, woollen and synthetic materials; iron the reverse side of the fabric to prevent
O = no steamshiny patches. Avoid using the spray function to prevent stains.
l = moderate steam
; = maximum steamStart ironing the articles that require the lowest ironing temperature, such as those
made of synthetic fibres.
x = Calc-Clean function
D Spray button T (GC1830/1820/1815/1720/1705)3 Put the mains plug in an earthed wall socket.
E Steam boost 9 (GC1830/1820/1815)
F Automatic shut-off light (GC1830 only)4 When the temperature light has gone out, wait a while before you start
ironing (fig. 5).
G Temperature light
H Mains cordThe temperature light will go on from time to time during ironing.
I Anticalc tablet (GC1830/1820 only)
J Type plateUsing the appliance.
K Water tankSteam ironing
L Temperature dial
1 Make sure that there is enough water in the water tank.
Important.
2 Select the recommended ironing temperature (see chapter 'Preparing for use',
Read these instructions for use carefully before using the appliance and save them forsection 'Setting the temperature').
future reference.
3 After the temperature light has gone out, set the steam control to the
� Check if the voltage indicated on the type plate corresponds to the localappropriate steam position. Make sure that the steam setting you select is
mains voltage before you connect the appliance.
� If the appliance is provided with an earthed plug, it must be plugged into ansuitable for the ironing temperature selected: (fig. 6).
earthed wall socket.l for moderate steam (temperature settings 2 to 3)
; for maximum steam (temperature settings 3 to MAX)
� Do not use the appliance if the plug, the cord or the appliance itself showsThe iron will start steaming as soon as the set temperature has been reached.
visible damage, or if the appliance has been dropped or is leaking.
� Check the cord regularly for possible damage.
� If the mains cord is damaged, it must be replaced by Philips, a service centreIroning without steam
authorised by Philips or similarly qualified persons in order to avoid a hazard.1 Set the steam control to position O (= no steam).
� Never leave the appliance unattended when it is connected to the mains.
� Never immerse the iron and the stand, if provided, in water.2 Select the recommended ironing temperature (see chapter 'Preparing for use',
� Keep the appliance out of the reach of children.section 'Setting the temperature').
� Young children should be supervised to ensure that they do not play with the
appliance.Features.
� This appliance is not intended for use by young children or infirm personsSpray function (specific types only)
without supervision.
� The soleplate of the iron can become extremely hot and may cause burns ifYou can use the spray function to remove stubborn creases at any temperature.
touched.
� Do not allow the cord to come into contact with the soleplate when it is hot.1 Make sure that there is enough water in the water tank.
� When you have finished ironing, when you clean the appliance, when you fill2 Press the spray button several times to moisten the article to be ironed
or empty the water tank and also when you leave the iron even for a short(fig. 7).
while: set the steam control to position O, put the iron on its heel and
remove the mains plug from the wall socket.Steam boost (specific types only)
� Always place and use the iron and the stand, if provided, on a stable, level and
horizontal surface.A powerful shot of steam helps to remove stubborn creases.
� This appliance is intended for household use only.
The steam boost function can only be used at temperature settings between 3
Before first use.and MAX.
1 Remove any sticker or protective foil from the soleplate.1 Press and release the steam boost button (fig. 8).
Wait a while before using the button again to avoid spluttering.
2 Let the iron heat up to maximum temperature and pass the iron over a piece
of damp cloth for several minutes to remove any residues from the soleplate.Never direct the steam at people.
BThe iron may give off some smoke when you use it for the first time. This will cease
Vertical steam boost (GC1830/GC1820/GC1815 only)
after a short while.
Preparing for use.1 The steam boost function can also be used when you are holding the iron in
vertical position. This is useful for removing creases from hanging clothes,
Filling the water tankcurtains, etc (fig. 9).
Never immerse the iron in water.Never direct the steam at people.
1 Make sure the appliance is unplugged.
Automatic shut-off (GC1830 only)
2 Set the steam control to position O (= no steam) (fig. 2).
The electronic shut-off function automatically switches the heating element off if the
3 Tilt the iron backwards.iron has not been moved for a while.
4 Fill the water tank with tap water up to the maximum level (fig. 3).� The auto-off light starts blinking to indicate that the iron has been switched off
Do not fill the water tank beyond the MAX indication.by the safety shut-off function (fig. 10).
Do not put perfume, vinegar, starch, descaling agents, ironing aids or other -In horizontal position, this will happen after 30 seconds.
-In vertical position, this will happen after 8 minutes.
chemicals in the water tank.� To let the iron heat up again:
� If the tap water in your area is very hard, we advise you to mix it with an-Pick up the iron or move it slightly. The auto-off light goes out.
equal amount of distilled water or to use distilled water only.-If the temperature light goes on, wait for it to go out before you start ironing.
-If the temperature light does not go on, the iron is ready for use.
Setting the temperature
Cleaning and maintenance.
1 Put the iron on its heel.After ironing
2 Set the required ironing temperature by turning the temperature dial to the1 Remove the mains plug from the wall socket and let the iron cool down.
appropriate position (fig. 4).
Check the laundry care label for the required ironing temperature:2 Wipe scale and any other deposits off the soleplate with a damp cloth and a
1Synthetic fabrics (e.g. acrylic, viscose, polyamide, polyester)non-abrasive (liquid) cleaner.
1SilkTo keep the soleplate smooth, you should avoid hard contact with metal objects.
2Wool
3 Cotton, linenNever use a scouring pad, vinegar or other chemicals to clean the soleplate.
4239 000 61501
2/9 |
ACEC
PHILIPS
