Connecting the Unit<ENGLISH>Installation<ENGLISH>
Using the Speaker InputConnecting the Speakers and InputTwo-channel mode (Stereo)Y Do not install the amplifier on unstable places
CAUTIONsuch as the spare tire board.
WiresY The best location for installation differs with the
Connect the car stereo speaker output wires to the amplifier using the supplied speaker inputY Do not install in:
Speaker (Right)car model and installation location. Secure the
connector.NPlaces where it could injure the driver or pas-
The speaker output mode can be four-amplifier at a sufficiently rigid location.
Y Do not connect both the RCA input and the speaker input at the same time.sengers if the vehicle stops suddenly.
channel, three-channel (stereo + mono) or+`Y Make temporary connections first and check that
NPlaces where it may interfere with the driver,
7 Connections when using the speaker inputtwo-channel (stereo, mono). Connect thesuch as on the floor in front of the driverOsthe amplifier and the system operate properly.
speaker leads to suit the mode according toY After installing the amplifier, confirm that the
Green: CH B, Left +seat.
the figures shown below.spare tire, jack and tools can be easily removed.
Y Make sure that wires are not caught in the sliding
Y In the case of four-channel or three-mechanism of the seats, resulting in a short-cir-
Green/black: CH B, Left `
channel mode, if only one input plug iscuit.Example of installation on the floor
used, such as when the car stereo hasY Confirm that no parts are behind the panel when
mat or on the chassis
only one output (RCA output), connectdrilling a hole for installation of the amplifier.
`+
the plug to RCA input jack A, but do notProtect all cables and important equipment such
Violet/black: CH B, Right `connect a plug to RCA input jack B.Speaker (Left)as fuel lines, brake lines and electrical wiring
1. Place the amplifier where it is to be
Y In the case of two-channel mode connectfrom damage.
Violet: CH B, Right +Y Install tapping screws in such a way that the installed. Insert the supplied tapping
RCA plugs to the RCA input jack A.
Car Stereoscrew tip does not touch any wire. This is impor-screws (4 � 18 mm) into the screw
Gray: CH A, Right +
Four-channel modeTwo-channel mode (Mono)tant to prevent wires from being cut by vibrationholes. Push on the screws with a
of the car, which can result in fire.
Gray/black: CH A, Right `
screwdriver so they make marks
Y DO NOT allow amplifier to come into contact
(Right)Speaker (Mono)with liquids due to, for example, the locationwhere the installation holes are to be
Speaker input connectorSpeaker output
Speaker out Awhere the amplifier is installed. Electrical shocklocated.
To speaker input termi-
(Left)`+could result. Also, amplifier and speaker damage,
nal of this unit.
White/black: CH A, Left `smoke, and overheating could result from contact
2. Drill 2.5 mm (1/8 inch) diameter
+``+with liquids. In addition, the amplifier surface and
the surface of any attached speakers could becomeholes at the point marked, and
White: CH A, Left +
hot to the touch and minor burns could result.install the amplifier, either on the
Y To ensure proper installation, use the supplied
carpet or directly to the chassis.
parts in the manner specified. If any parts other
than the supplied ones are used, they may damageTapping-screws
+`internal parts of the amplifier, or they may(4 � 18 mm)
+``+
Speaker (Mono)become loose causing the amplifier to shut down.
(Left)Y Never replace the fuse with one of greater value
Speaker out Bor rating than the original fuse. Use of an improp-
(Right)er fuse could result in overheating and smoke and
could cause damage to the product and injury
including burns.
Three-channel mode
CAUTION:
(Right)To prevent malfunction and/or injury
Speaker out AY To ensure proper heat dissipation of the amplifier,Floor mat
(Left)be sure of the following during installation.or chassis
Drill a 2.5 mm (1/8 inch)
NAllow adequate space above the amplifier for
+``+diameter hole
proper ventilation.
NDo not cover the amplifier with a floor mat or
carpet.
Y DO NOT allow amplifier to come into contact
with liquids due to, for example, the location
where the amplifier is installed. Electrical shock
+`could result. Also, amplifier and speaker damage,
Speaker out Bsmoke, and overheating could result from contact
(Mono)with liquids. In addition, the amplifier surface and
the surface of any attached speakers could become
hot to the touch and minor burns could result. |
ACEC
PIONEER
