JVC GRAX970U Repair Manual

$7.99

JVC GRAX970U - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

HIROSHI EMOTO - 11/29/2007

Very fast service and a good documents. Thank you.

John Craig - 07/31/2006

Very nice site and the manual is great. A life-saver. Thank you so much!

Jason Gaunt - 01/26/2008

This manual is for both the EU and Australian version of the CCD-TR55(E) Camcorder, as stated it includes both the users manual and the service manual. The quality of the manual is very good but it is only black and white (not full colour) and ultimately it is just a scan, so 4/5 from me.

Othmar Herbst - 01/13/2008

PDF contains : - schematics, but a little un-sharp. - disassembly instructions, accurate drawings - description of test-modes

Gaspar Lovas - 11/03/2009

That's all right, thank you for all your trouble. Yours sincerely GL

Customers who bought this product also purchased

JVC 20AV21TE Service Manual	JVC 28KH1SUF Service Manual	JVC 4DD-5 Owner's Manual
JVC 1702 Service Manual	JVC 15A5 Service Manual	JVC AL-E77BK Service Manual

Click to see text excerpt from the manual

1.5 REPLACEMENT OF 3 CCD IMAGE SENSORPart NameOrientation
Notes:CCD image sensorMark is on the right viewed as indi-
YPay the most careful attention to the transparent glass andcated by the arrow a .
optical LPF of the CCD image sensor so a not the soil andSpacer rubberIC side is horizontal.
damage them. If something is soiled with finger-prints, etc.,
gently clean it with silicon-processed paper/cloth or cham-Optical LPFMarks are on the left and bottom
ois.viewed as indicated by the arrow
a .
YWhen the CCD image sensor is shipped from the factory,
there are protection seals applied onto the transparent2. Fix the CCD base assembly to OP block with the two
glass. Leave the protector as it is, and take it off just be-screws (S1a) . At that time, be careful of the orienta-
fore assembling the CCD image sensor to the OP block.tion.
3. After completion of all P.C. boards to the camera sec-
1.5.1 Removal of CCD image sensortion, observe the monitor to confirm no vignetting caused
by the bodytube, rings, lens hood, etc. If no vignetting
1. Remove two screws (S1a) securing the CCD base assy,is observed, it can be said that image's parallel,
and disassemble the CCD spacer, the optical LPF,horizontality and centering are correct.
spacer rubber.
1.5.3 Replacement of CCD board assembly
1.5.2 Installation of new CCD image sensor
1. Remove the protection seal from a new CCD image sen-1. Remove one screw (S1b).
sor. Next, put the optical LPF, spacer rubber, CCD2. Unsolder at the fourteen points on the CCD board as-
spacer on the CCD image sensor as they are piled upsembly.
in this order. At that time, make sure of orientation of eachNotes:
item refering to the following table (see Fig. 1-5-1).
YRemove the screw (S1b) only when the CCD board as-
sembly needs replacement.
YWhen installing a new CCD board assembly, carry out the
above-mentioned procedure in the reverse order.
a
OPTICAL LPF3
1
(S1 b)
BLUE(S1 a)
CCD
SIDE
CCD BOARD2
OPASSEMBLY(S1 a)
SIDE
CCD BASE ASSEMBLY
CCD SPACER
SPACER RUBBER
: 0.147 NYm (1.5 kgfYcm)
Fig. 1-5-1
1-10