1798/2301-2
Viewing Result Mode Data?The format (12-hour and 24-hour) of the alarm time matches the format you select
Press BBBBB to cycle through the best five lap times. Pressing AAAAA while a lap time is onfor normal timekeeping.
the display shows the average speed for the lap. Press AAAAA again to return to the lap?When setting the alarm time using the 12-hour format, take care to set the time
time.correctly as morning or afternoon.
?Pressing BBBBB while the average speed is on the display advances to the next lap4.After you set the alarm time, press AAAAA to return to the Alarm Mode.
time.?If you do not operate any button for a few minutes while a selection is flashing, the
?If the average speed is 1000 km/h or more, E r r is displayed in place of the averageflashing stops and the watch goes back to the Alarm Mode automatically.
speed.
To stop the alarm
Lap numberOrder?Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on and off
Press BBBBB while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Mode indicatorTime Signal in the following sequence.
Stopwatch type
indicator
Both OFFDaily AlarmHourly TimeBoth ON
OnlySignal Only
Lap time
Total time
To test the alarm
Hold down BBBBB while in the Alarm Mode to sound the alarm.
Single Stopwatch
Note that this operation also changes the Daily Alarm and Hourly Time Signal on/off
setting.
Lap numberOrder
(first starter)(first starter)
H-SET MODE
When the time shown on the display does not match the analog setting, use this
mode to correct the analog setting.
Mode indicator
Stopwatch type
indicator
Lap time
(first starter)
Lap number
(second starter)
Lap time
(second starter)
Order
(second starter)HourSeconds
Dual StopwatchMinutes
Deleting Result Mode DataTo set the analog time
Result Mode data is deleted automatically whenever you perform a new stopwatch1.Hold down AAAAA while in the H-SET Mode until the digital time (hour and minutes)
timing operation. To manually delete data, hold down BBBBB and DDDDD in the Result Modestarts to flash on the display.
until the message CLR appears on the display.?The following step changes the hands of the analog time-
piece without changing the flashing digital time.
2.Press DDDDD to advance the hand setting of the analog time-
piece. Holding down DDDDD changes the hand setting at high
speed.
DUAL TIME MODE?Pressing BBBBB while holding down DDDDD causes the hand set-
ting to change at high speed. The hands continue to
To set the Dual Timemove even when you release the buttons. Press DDDDD or
Mode indicator1.Hold down AAAAA until the hour digits start to flash on theBBBBB to stop them.
display. The hour digits flash because they are select-?The analog time setting does not stop automatically when
ed.Flashingit reaches the current time. You must stop the hands
2.Press CCCCC to change the selection in the following se-manually.
quence.?Note that there is not function for moving the hands back,
so be sure that you stop any high-speed hand setting
HourMinutes
operation before the time you want to set is reached.
3.After you set the analog time, press AAAAA to return to the H-SET Mode.3.Press DDDDD to increase the number or BBBBB to decrease it.
?If you do not operate any button for a few minutes while a selection is flashing, the
Holding down either button changes the current num-
flashing stops and the watch goes back to the H-SET Mode automatically.
ber at high speed.
HourSeconds4.After you set the dual time, press AAA to return to the
MinutesAA
Dual Time Mode.
?The format (12-hour and 24-hour) of the dual time match-
es the format you select for normal timekeeping.
?In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
?If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Dual Time Mode automatically.
Switching Dual Time and the Current Time
Holding down BBBBB for about two seconds in the Dual Time Mode causes the Dual Time
and current time to be reversed. The hands of the watch move at high speed to the
correct time. To switch back, simply hold down BBBBB again in the Dual Time Mode.
ALARM MODE
Mode indicatorWhen the Daily Alarm is turned on, an alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
1.Hold down AAAAA until the hour digits start to flash on the
display. The hour digits flash because they are select-
ed. At this time the Alarm is automatically switched on.
2.Press CCCCC to change the selection in the following se-
quence.
HourMinutes
Hour Minutes
3.Press DDDDD to increase the number or BBBBB to decrease it.
Holding down either button changes the current num-
ber at high speed. |
ACEC
CASIO
