90404-gb.fm5 Page 3 Thursday, September 22, 2005 5:50 PM
Troubleshooting Guide
Tips and advice Before starting a wash programme, Crockery still dirty after washing:
Arrange crockery so that items do not make sure that the spray arms can turn Was the crockery loaded properly?
AFTER-SALES
freely and are not impeded by crockery
touch each other. Arrange large Crockery must be loaded facing
or cutlery.
crockery in the lower rack and smaller downwards; this is important, especially SERVICE
crockery in the upper rack. Only switch off the dishwasher once thfor large items of crockee ry.
?Start? indicator mp has switlached off.If after carrying out the above checks
Load cups at an angle to facilitate The water jets must spray the entire the malfunction persists or appears
If the dishwasher is switched off during
water drainage.surface of all items.again, turn the appliance off and turn
a wash cycle, when switched on again
off the water supply tap, then call
Generally speaking, place cutlery in the it will resume the cycle from where it Make sure that crockery and cutlery are
our After-Sales Service (see guarantee).
basket with the handles positioned was interrupted without having to start arranged properly.
Please specify:
downwards, but ensure that any sharp it again. Have you selected the correct programme?
The nature of the fault.
knives and forks that might cause Did you use too much or too little detergent?
The appliance type and model.
injury are placed in the basket with the (The use of poor quality detergents may
The service code (the number after
handles positioned upwards.result in less effective washing).
the word Service on the adhesive
If a fault occurs, before contacting our
Make sure the water jet can reach all Are the filters clogged or incorrectly
After-Sales Service, make the following rating plate) inside the door on the
loaded items and that the spray arms assembled? (See a?Cre and Maintenance?
checks to try and remedy the problem:right-hand side.
turn freely.chapter in the user instructions).
The dishwasher is not working:
Important Is the plug properly inserted in the wall Are the spray arms blocked or the nozzles
Fill the detergent dispenser and check socket?clogged? (See ?Care and Maintenance?
the salt and rinse aid level. Is there a power failure?chapter in the user instructions).
Is the dishwasher switched on? Is the lower spray arm correctly fitted?Your full address and telephone
Do not use the appliance for items not
Has the Start button been pressed?number.
suitable for washing in a dishwasher, Is the salt container cap (water softening
Has the delayed start timer been set (if
for example: wooden items, aluminium, system) screwed down?
fitted)?
plastic utensils, tin, hand-decorated Marked crockery:
Is the water supply tap on?
crockery (unglazed), silver cutlery. Is the water hardness level selector not
Is the flow of water obstructed by
Do not put liquid fat in the dishwasher impurities? If so, close the water suppproperly adjusted? See (?Filling thely salt
(e.g. oil used for frying) or candle wax.tap, detach the water hose and clean the container? in the user instructions).
If a fault occurs or you wish to chanfilter. Then ge re-connect the water hose to Is the salt container empty? (See ?Filling
the tap and open the water tap once the salt container? in the user
the current programme, press the
again.
?START? button for about 5 seconds until instructions).
Are the filters clogged? (See ?Care and
the Start indicator lamp switches off. Was insufficient detergent used? (See
Maintenance? chapter in the user
?Filling the detergent dispenser? in the
If regeneration salt is to be added, instructions).
user instructions).
immediately start a wash programme Is the door closed properly?
Marked glasses and cutlery:
in order to eliminate any residual salt Is a fault indicated?
(rinsing alone is not sufficient).(The Start indicator lamp flashes). Was too much rinse aid used? (See
?Filling the rinse aid dispenser? in the
Sometimes, even though the Start the programme again from the
regeneration salt container has been beginning: press the Start button for user instructions).
filled, the corresponding indicator about 5 seconds, until the Start indicator lamp Note: with some models, when the Start
lamp switches off.button is pressed a pre-wash cycle precedes
(if fitted) will light up during the first
wash cycle after filling with salt.Select a new programme and press the the actual wash programme; this
Start button.regenerates the water softening system.
Please read the user instructions carefully. |
ACEC
BAUKNECHT
