Troubleshooting Guide
Tips and advice Before starting a wash programme, Crockery still dirty after washing:
Arrange crockery so that items do nomat ke sure that the spray arms can turn Was the crockery loaded properly?AFTER-SALES
touch each other. Arrange large freely and are not impeded by crockery Crockery must be loaded facing
crockery in the lower rack and smallor cuer tlery.downwards; this is important, especially SERVICE
crockery in the upper rack. Only switch off the dishwasher once the for large items of crockery.
?Star?t indicator lamp has switched off.If after carrying out the above checks
Load cups at an angle to facilitate The water jets must spray the entthire me
alfunction persists or appears
If the dishwasher is switched off during a
water drainage.surface of all items.again, turn the appliance off and turn
wash cycle, when switched on again it
Generally speaking, place cutlery in the Make sure that crockery and cutlery off the water suare pply tap, then call our
will resume the cycle from where it was
basket with the handles positioned arranged properly.After-Sales Service (see guarantee).
interrupted without having to start it Please specify:
downwards, but ensure that any sharp
again. Have you selected the correct programme?
knives and forks that might cause The nature of the fault.
Did you use too much or too little detergent?
injury are placed in the basket with the The appliance type and model.
(The use of poor quality detergents may
handles positioned upwards. The service code (the number after
result in less effective washing).
Make sure the water jet can reach all the word Service on the adhesive
If a fault occurs, before contacting ouAre the filr ters clogged or incorrectly
loaded items and that the spray armsAfter-Sales Service, make the following rating plate) inside the door on
assembled? (See ?Care and Maintena?nce the right-hand side.
turn freely.checks to try and remedy the problem:
chapter in the user instructions).
ImportantThe dishwasher is not working:
Is the plug properly inserted in t hAre te walhle spray arms blocked or the nozzles
Fill the detergent dispenser and check
clogged? (See ?Care and Maintena?nce
the salt and rinse aid level. socket?
Is there a power failure?chapter in the user instructions).
Do not use the appliance for items not Your full address and telephone number.
Is the dishwasher switched on? Is the lower spray arm correctly fitted?
suitable for washing in a dishwasher,
Has the Start button been pressed?
for example: wooden items, aluminium, Is the salt container cap (water softening
Has the delayed start timer been set (if
plastic utensils, tin, hand-decorated system) screwed down?
fitted)?
crockery (unglazed), silver cutlery.Marked crockery:
Is the water supply tap on?
Do not put liquid fat in the dishwasher Is the water hardness level selector not
Is the flow of water obstructed by
(e.g. oil used for frying) or candleim wpuaritx.ies? If so, close the water psuroppperlly y adjusted? Se?File (ling the salt
If a fault occurs or you wish to change tap, detach the water hose and cleacon thntae ine? ir n the user instructions).
the current programme, press the filter. Then re-connect the water hos Is the te o salt container emp?tFilly? (Seeing
?START ? button for about 5 seconds untithel tap and open the water tap once the salt cont?ai inne thr e user
the Start indicator lamp switches off.again.instructions).
If regeneration salt is to be adde d, Are the filters clogged? (See Was insufficient detergent used? (See
immediately start a wash programme ?Care and maintena?n chce apter in the ?Filling the detergent di? inspe thnsee r
in order to eliminate any residual sauser inlt structions).user instructions).
(rinsing alone is not sufficient). Is the door closed properly?Marked glasses and cutlery:
Is a fault indicated?
Sometimes, even though the Was too much rinse aid used? (See
(The Start indicator lamp flashes).
regeneration salt container has been ?Filling the rinse aid di? inspe thne useser r
Start the programme again from the
filled, the corresponding indicator lamp instructions).
beginning: press the Start button for
(if fitted) will light up during the first
about 5 seconds, until the Start Nointe:dica wittohr some models, when the Start
wash cycle after filling with salt.
lamp switches off.button is pressed a pre-wash cycle precedes
Select a new programme and press tthhe ae ctual wash programme; this
Start button.regenerates the water softening system.
Please read the user instructions carefully. |
ACEC
BAUKNECHT
