Guided Tour - HA4000 Rear Panel
111 12
ENGLISH
CAUTION
POWERRATING115V/230V 50HZ/60Hz 740WCAUTION
8A/250V(115V)FUSE4A/250V(230V)TO PREVENT SHOCK,DO NOT OPEN. NO USER SERABLE PSERHAZARD. DO NOT EXPOSE TO RAIN OR MOISTURE.VICE PERSONNEL. TO PREVENT FIRE OR SHOCKARTS INSIDE. REFER SERVICING TO QUALIFIEDVICE-Distributed Exclusively bySamson Technologies Corp.AVIS;RISQUE DE CHOC ELECTRIQUEDO NOT EXPOSE THIS EQUIPMENTNE PAS OUVRIR
CAUTION; REPLACE WITH THEMODEL HA4000 (400 WATTS)RISK OF ELECTRIC SHOCKDO NOT OPENTO RAIN OR MOISTURE.
UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE. 4& = 400 WATTSDIRECT OUTPRE AMP OUTSAME TYPE FUSE AS INDICATED. 8& = 290 WATTS
S / N400WSPEAKER OUTPUTATT RMS/4ohmsCHASSIS GROUND
115/230V~AC INPUT, 50/60HzLIFT REMOVES
CHASSIS GROUNDFROM XLR PIN1
MUTE FOOTSWITCH<SEND PRE50& 0dBuRETURN PRE10K& 0dBuSEND POST<50& 0dBu RETURN POST10K& 0dBuTUNER OUT<50& 20dBuS BASS OUT<50& +4dBu<LINE OUT50& +4dBu<100BALANCED& �20dBu<100BALANCED& �20dBuFRAMEGROUNDFLOATMADE IN KOREA
2 3 4 5 6 7 8 9 1013 1415
1. Fuse holder- Holds a 8A/250V fuse for 115 volt operation or a 4A/250V fuse for
230 volt operation
2. AC input - Connect the supplied standard 3-pin OIEC� plug here.
3. Mute Footswitch - Connect a standard single-pole latched (maintained contact)
footswitch to this 1/4" unbalanced jack here. To activate the footswitch, press in the front-
panel Audio Mute switch (see #1 on page 5) so that it is in the Oin� (down) position, then
step on the footswitch. When you next step on the footswitch, all of the HA4000 outputs
except the rear-panel Tuner Out (see #8 on page 8) are temporarily silenced, muting audio
signal and allowing you to easily tune your bass between songs. To restore audio signal to
all outputs (including the Tuner Out, which is always active), simply step on the footswitch
again. To disable the footswitch, press the front-panel Audio Mute switch so that it is in the
Oout� (up) position
4. Send Pre - Use this 1/4" unbalanced jack to send signal to a professional outboard
effects processor.* Output level is approximately 0 dB to +4 dB and is pre-EQ and
pre-Shape but post-Volume control.
5. Return Pre- Use this 1/4" unbalanced jack to return signal from a professional outboard
effects processor.* Signal is returned before the EQ and Shape controls but after the
Volume control.
6. Send Post - Use this 1/4" unbalanced jack to send signal to a professional outboard
effects processor.* Output level is approximately 0 dB to +4 dB and is post-EQ,
post-Shape, and post-Volume control.
7. Return Post- Use this 1/4" unbalanced jack to return signal from a professional
outboard effects processor.* Signal is returned after the EQ, Shape and Volume controls.
* In-line effects (such as footpedals) intended for low signal levels should be placed
between your bass and the front panel HA4000 Input and not connected with the rear
panel Send/Return jacks.
9 |
ACEC
OTHERS
