FRONT PANEL FEATURES
17. Crossfader Direction: Activation of this
switch reverses the assignment of CH-1 and
CH-2 on the crossfader.
18. Crossfader Contour Control: The position
of this control determines how quickly or
intensely the crossfader will blend.
19. Master Output Knob: This rotary control
adjusts the main output volume.
20. Stereo Level Indicator: quickly and
accurately tracks level of audio.
21. Sub Bass: Reproduces sub-harmonic
frequencies one octave below and adds them
to the original signal. The result is increased
bass.
REAR PANEL FEATURES
1. Power LED: Illuminates when the mixer is on. Note: It is recommended that the mixer be
2. Mic Gain: This knob adjusts the volume of the turned off before connecting and disconnecting
microphone input. any sources to the inputs of the mixer.
3. Mic Treble: This knob adjusts the high-tone
of the microphone. 1. Microphone Input: Microphones with a 1?
4. Mic Bass: This knob adjusts the low-tone of connector can be connected to this input
the microphone. terminal.
5. Channel Gain: This rotary control adjusts 2. Phono Inputs: This input is used for connecting
the pre-fader input level. your turntables through the sensitive RIAA phono
6. Channel Treble: This rotary control adjusts preamplifiers. Only turntables with phono level
the high-tone level. output should be attached. Line level turntables
7. Channel Middle: This rotary control adjusts and other devices may be attached if the
the middle-tone level. Phono/Line rear panel switch is set to the line
8. Channel Bass: This rotary control adjusts the position.
low-tone level. 3. Phono/Line Source Switch: This switch
9. Input Selector: This toggles select what activates and deactivates the sensitive RIAA
input source is routed to the channel from the phono preamplifiers. Only turntables with
rear panel connected units. phono level output should be assigned when
10. Channel Fader: This slide fader is used to the switch is in the phono position. Some
adjust the level sent to program mix. turntables offer line level output. To use these
11. Headphone Volume: This rotary control turntables and other line devices like CD players,
adjusts the volume level of the headphone switch the input to Line.
output. 4. GND: This screw connector should be used to
12. Headphone Jack: Your headphones can be secure any turntables or other devices connected
connected to this 1? terminal. The volume to the mixer that need to be grounded.
should always be set at its lowest setting while 5. Line Inputs: CD players, Tape Decks, Samplers
connecting and disconnecting headphones to or other line level input devices should be
prevent damage to headphones and/or your connected to these inputs.
hearing. 6. Record Output: This RCA output is for
13. Cue Slider: Channels 1 and 2 can be connecting a recording device such as a tape deck
previewed using this mini-crossfader. Sliding or CD recorder. The level of the record output is
this to the left plays the left ?channel-1? and based upon pre-master levels.
sliding to the right plays the right ?channel-2?. 7. Master Output (RCA): This output is for
14. Cue Meter: This meter shows the peak, connecting an external monitoring device such as
?PFL?, Pre Fader levels of channels 1 and 2. a PA system, powered monitors or a home stereo.
You can use the channel ?Gain? and ?EQ? The level of the master stereo output signal is
controls to match the levels of input signals controlled by the master fader.
while cueing. 8. AC In: This mixer is designed to work with the
15. Master Cue Selector: When selected only the power supply assembly that comes with the unit.
master output is heard in the headphones. While the power is switched off, plug the power
16. Replaceable Crossfader: This slide fader supply into the mixer first, then plug it into the
blends audio between the channels assigned outlet.
to the left and right assign switches. 9. Power Switch: Use this switch to turn on the
Note: This fader is user replaceable if it mixer after all input devices are already
should ever wear out. Simply remove the connected to prevent damage to your equipment.
facepanel and then remove the screws holding Turn the mixer on before you turn on amplifiers
it in position. Replace the fader with a quality and turn of amplifiers before you turn off the
authorized replacement from your local mixer.
Numark retailer. |