AIWA CDCMA01 Repair Manual

$7.99

AIWA CDCMA01 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Wednesday 21 November, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Peter Rawson - 08/02/2006

Wow! I thought I wouldn't be able to find manual for such rare equipment like KM2000E. And here it is! Thanks for fast service!

Henry Seiden - 02/26/2009

I downloaded this product and looked through it quickly with Adobe Reader v9. It is clean and a good copy. Some scanned pages are not perfectly square, but that is a minor complaint. The document schematics and board diagrams are easy to read, of good contrast. The whole file downloaded quickly. This is a good service! Sony charges about $100 for the printed version of the same manual. It is still available through their print-on-demand pro parts system, but why would you do that?

James Thorp - 12/28/2006

Great original Yamaha manual and no problems at all with the ordering process. Will definitely use this website again and would recommend it to anyone else. James Thorp

oleg volkozub - 09/25/2008

Very nice clear manual with specifications, thanks!

Fabian Castle - 08/01/2006

Thanks for the excellent service. The manual arrived quickly and in excellent condition. Quality A+++!

Customers who bought this product also purchased

AIWA 2002 Service Manual	AIWA 2ME-4 Service Manual	AIWA 2ME7 Service Manual
AIWA 2ME-1 Service Manual	AIWA ADC-EX108YU Service Manual	AIWA ACL-M200 Service Manual

Click to see text excerpt from the manual

Pin No.Pin NameI/ODescription
1DVDD0Ä�Digital power supply.
2XRSTISystem reset. Reset when low.
3MUTEIMute input. (L: OFF, H: ON)
4DATAISerial data input from CPU.
5XLATILatch input from CPU. Serial data is latched at the falling edge.
6CLOKISerial data transfer clock input from CPU.
7SENSOSENS output to CPU.
8SCLKISENS serial data readout clock input.
9ATSKI/OAnti-shock input/output. (Connected to digital GND)
10WFCKOWFCK output. (Not used)
11XUGFOXUGF output. MNT0 or RFCK is output by switching with the command. (Not used)
12XPCKOXPCK output. MNT1 is output by switching with the command. (Not used)
13GFSOGFS output. MNT2 or XROF is output by switching with the command.
14C2POOC2PO output. MNT3 or GTOP is output by switching with the command.
15SCOROOutput a high signal when either subcode sync S0 or S1 is detected.
4.2336 MHz output. 1/4 frequency division output for V16M in CAV-W mode or variable pitch
16C4MOmode. (Not used)
17WDCKOWord clock output. f = 2Fs. GRSCOR is output by the command switching. (Not used)
18DVSS0Ä�Digital GND.
19COUTI/OTrack count signal input/output.
20MIRRI/OMirror signal input/output. (Not used)
21DFCTI/ODetect signal input/output.
22FOKI/OFocus OK signal input/output.
23PWMIISpindle motor external control input.
24LOCKI/OGFS is sampled at 460 Hz; when GFS is high, this pin outputs a high signal. If GFS is low eight
consecutive samples, this pin outputs low. Input when LKIN = 1.
25MDPOSpindle motor servo control output.
26SSTPIDisc innermost track detection signal input.
27FSTOO2/3 frequency division output for XTAI pin. (Not used)
28DVDD1Ä�Digital power supply.
29SFDROSled drive output.
30SRDROSled drive output.
31TFDROTracking drive output.
32TRDROTracking drive output.
33FFDROFocus drive output.
34FRDROFocus drive output.
35DVSS1Ä�Digital GND.
36TESTITest. (Connected to digital GND)
37TES1ITest. (Connected to digital GND)
38VCICenter voltage input.
39FEIFocus error signal input.
7