GRUNDIGServiceSTR 6100
The status display
1If you press the . key on the remote control unit4A value which can be changed is flashing in the
once, the status menu is briefly displayed on themenu (CURSOR). Change a value with the xcrLNC oscillator frequencies ($)rReceiver lock ())
picture screen.keys. Numeric values can be changed at fast speed6The receiver is preprogrammed for the following1You can lock your receiver.
by pressing and holding down the xc keys. LNC oscillator frequencies:
&300In most cases, a direct entry of the value is alsoReceiver not locked:")X"
}11.494 GHZSelection A, 22 KHz off: 9750 MHzReceiver locked:")3"
possible.
$V�ASelection A, 22 KHz on: 9750 MHz
+ź7.02 MHZ 7.20 MHZ Selection B, 22 KHz off: 9750 MHz6If you lock your receiver and then switch it to stand-
Press the Okey to save the changes made. This
ź~PANDA5by, it can be switched on again only by entering the
automatically closes the corresponding menu andSelection B, 22 KHz on: 9750 MHzcorrect key combination.
briefly displays the status menu.If you should use an LNC having a different oscilla-
All programme positions and all menus are locked.
´16:35tor frequency, you can change the corresponding
6To exit a menu without saving, press the . key.setting.When the receiver is locked
61: ´2: &3: }The changes made are undone and the status menu
is briefly displayed. 1Use the xc keys to change the value step by1If you lock your receiver and then switch it on from
Meaning of symbols:step, or the numeric keys to enter the value directly.standby, the following display appears:
Settings&300Programme position "). . . ."
number2If you use several LNC's, you must check all oscil-
The system setup menu
}11.494 GHZSatellite channel transmis-lator frequencies and correct them if necessary.
2Each dot stands for a key. When pressing a key, the
sion frequencySettings
corresponding dot is replaced by a small line.
$V�ALNC setting: polarizationV/H,rOverview
22 kHz switching frequencyrLNC voltage supply on/off ($%)
3Press the cx |] keys on the remote control
off (�)/on (~), 1Press the . key and then the 3 key.
satellite selection A/BOn the picture screen appear the status menu and6With the default setting made at the factory, theunit one after the other.
+ź7.02 MHZ 7.20 MHZLeft and right audio then the system setup menu.receiver provides for the voltage supply of the satel-
frequencylite aerial.w!This code
ź~PANDADeemphasis/noise $�A09.750 GHZ1If your receiver is connected along with other cannot be
suppression$~A09.750 GHZreceivers to a communal aerial system (single cablechanged.
´16:35Time$�B09.750 GHZNote it down
61: ´ 2: & 3: }Key functions:$~B09.750 GHZinstallation), switch the LNC voltage supply offand keep it
6: cancel status display$%3("$%X"), if not, leave the "$%3" setting.in a safe
instantly,W144
place.
1: ´ open Timer menu,W230Contrast levels 1 and 2 presettings
2: & open "Programme/1r6After entering the correct code, the receiver can be
position setup" menu,)X(W1, W2)used again. Switching the receiver to stand-by will
3: } open "System setup"6/ OKlock it again.
menu.6You can select one of the two contrast levels in the
"Programme position setup" menu.
6The time can be set in the Timer menu. The remain-6Meaning of symbols:6When the receiver is switched on, the lock may be
!
ing settings (transmission frequency, LNC setup,wIf possible,cancelled at any time in the menu.
audio settings) are made in the "Programme posi-$�A09.750LO frequency of LNC without 22 kHzthe preset
tion setup" menu.switching signal, satellite selection A.values
$~A09.750 LO frequency of LNC with 22 kHzshould notThe programme position setup
switching signal, satellite selection A.be
menu
The on-screen menu guide$�B09.750LOfrequency of LNC without 22 kHzchanged, as
switching signal, satellite selectionBthis would
6The receiver is already preprogrammed for the cur-
1Call up the status menu by pressing the . key. As$~B09.750 LO frequency of LNC with 22 kHzalso change
rent channels of many satellites. In most cases, a
long as this menu is displayed, you can call up theswitching signal, satellite selection Bthe contrast
correction is not required.
remaining three menus by means of the numeric$%3LNC voltage supply on/off.setting of all
keys 1�3. W144Contrast level 1 preset.other pro-
6However, new programmes are continuously added
W230Contrast level 2 preset.grammeor transmission frequencies are changed. The
6For a displayed menu, the following key functions/1Decoder mode selectionpositions.
current state of the transmission frequencies can be
apply principally (these functions will not be)XReceiver lock yes/no.
1In exceptional cases, you can change the contrastcalled up by means of the Teletext pages of various
explained again in the menu descriptions).6/ OK6: exit menu,
level by means of the xc keys.stations (e.g. Sky News: Teletext page 675), or
OK: save and exit menu.the information required can be found in TV pro-
2If you do not wish the TV picture as background,
gramme guides. Changed programmes then can be
you can display a blue background by pressing therDecoder mode selection (/)Allgemeiner Teil / General Section
re-programmed in the programme position setup
cTXTkkey. Pressing the cTXTkkey again restores the
TV picture as background.1You have the choice between the following decodermenu.
modes:
6In the "Programme position setup" menu, you have
3When in a menu, use the ]| keys to select1Normal
access to the picture and sound settings of the indi-
menu options or values.
2PALvidual programme positions.
3Baseband
Use the numeric keys or the ]| keys to select
4MAC (for D2MAC decoder)1
the programme position for which you wish to
6For detailed information, see the operating instruc-check or change the settings.
tions of the decoder.
w!It is not pos-
sible to sel-
1 - 11 |
ACEC
