GV 29 EURO, GV 9300 EURODrive Mechanism
8.8 Brake Actuating Lever (Pos. 31100), Brake Control Lever
20120 Screw
(Pos. 31000)
� Remove the driving system of the cassette mechanism and crescent
20130slide (see point 8.3).
Mounting20100 � Remove the reel belt (Pos. 20800, Fig. 8.21).
clip, brake bandReel
� Disengage clamp J, then clamp K and remove the brake control
lever (Pos. 31000, Fig. 8.22).
� Detach the brake return spring (Pos. 31300) and the clutch change
20600
lever spring (Pos. 31200, Fig. 8.22).
Gear, reel s
20110 Special washer� Disengage clamp L, then clamp M and remove the brake actuating
lever (Pos. 31100, Fig. 8.22).
Notes on lubricating the brake actuating lever (Pos. 31100)
� Always use grease with part number 75988 061 7800 for lubricating
the brake actuating lever (Pos. 31100).
� Follow the lubrication instructions given in Fig. 8.22!
Shaft
31300 Brake return spring
31000 Brake controldeutsch Y German Y allemand
Apply grease lever
31200Spring, clutch
(part no.
change lever
75988 061 7800).
31100 Brake
40200
actuating lever
Brake band
Apply grease ClampJ
Apply grease
(part no. 75988 061 7800)
(part no.
to the shaft
75988 061 7800)
Fig. 8.20
ClampL
MClamp
8.7 Pulley with Friction Clutch (Pos. 20500) and Clutch GearClampK
(Pos. 2030A)
Shaft
� Detach the reel belt (Pos. 20800), remove the retaining washer
(Pos. 20510) and remove the pulley together with the friction clutch
(Pos. 20500, Fig. 8.21).
� Remove the clutch spring (Pos. 20400), remove the retaining
washer (Pos. 20310) and the clutch gear (Pos. 2030A, Fig. 8.21).
Notes on lubricating the pulley shaft and clutch gear (Pos. 2030A)Apply grease
� Always use the types of lubricants with part numbers 75988 061(part no. 75988 061 7800)
7700, 75988 061 7800 for lubricating the pulley shaft and the clutch
gear (Pos. 2030A).
� Follow the lubrication instructions given in Fig. 8.21!Fig. 8.22
8.9 Crescent Slide (Pos. 60600)
� Remove the driving system of the cassette mechanism and crescent
20510 Retaining washer
20800 Belt, reelslide (see point 8.3).
� Remove the reel belt (Pos. 20800, Fig. 8.21).
Pulley,
� Detach the brake return spring (Pos. 31300, Fig. 8.22).
friction clutch
20500� Undo screw (Pos. 60710) and remove the crescent slide mounting
(Pos. 60700, Fig. 8.23).
� Disengage the clamp N and remove the crescent slide (Pos. 60600,
20400Fig. 8.23).
Apply grease
Spring, Note: Before reassembling the crescent slide (Pos. 60600) the
(part no.
clutchthreading roller units (Pos. 5050A and 5060A) are to be
75988 061 7800)
positioned so that they are in Eject mode (Fig. 8.23). When
20310
Clamps
Retaining washerfitting it, lift the right side of the crescent slide (Pos. 60600)
2030A Gear, slightly, insert the left side into the clamp N first, and align
clutchthe hole O with the pin P of the tension arm (Pos. 40400).
2030B Special Notes on lubricating the crescent slide (Pos. 60600)
washer� Always use grease with the part number 75988 061 7800 for lubri-
312001010D Retaining
cating the crescent slide (Pos. 60600) and follow the lubrication
Spring, clutchwasher
change lever1010B Lever, instructions given in Fig. 8.23 and Fig. 8.24!
clutch
Shaft
Apply a drop of oil
to each position
(part no. 75988 061 7700)
Fig. 8.21
GRUNDIG Service5 - 25 k |
ACEC
