HITACHI CPX345WF Repair Manual

$7.99

HITACHI CPX345WF - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

matt wilschke - 03/07/2008

Essential for popping the top open and cleaning and replacing what needs repalced. One note: the Ornamental Panel is attached with some adhesive as well as screws and faders so don't be shy about prying it open.

Aaron Lawrence - 01/02/2008

Contains mechanism diagrams, parts lists and schematics for all worldwide versions of DC-X88Z. Also includes remote schematic etc. A few non-essential pages are missing such as specifications. Includes the mechanical and electronic calibration instructions for the tape decks.

Fabian Castle - 08/01/2006

Thanks for the excellent service. The manual arrived quickly and in excellent condition. Quality A+++!

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

Dutra Lacerda - 02/17/2008

All schematics for the Euro-PC and some extra info. Needed if you want to replace some missing hardware. A piece of great historical value and for vintage computing entusiasts.

Customers who bought this product also purchased

HITACHI 13VR3B Owner's Manual	HITACHI 12220 Service Manual	HITACHI 42HDS52A Service Manual
HITACHI 12220T Service Manual	HITACHI 10214 Service Manual	HITACHI 192R Service Manual

Click to see text excerpt from the manual

Wiring power supply unit (When assembling board block sub-assembly) Wiring when assembling control panel
Connect CNPWR to ballast power source CN1.
Completely lock the connection.
Wiring when assembling power supply unit
Route the lead as shown below,
(1) Wire CNPOW and TSW.WARNING
and be careful of pinching in parts
(2) Connect and wire CNPWR.
Route CNPOW and TSW through (heat discharge plate, igniter trans., etc.).
(3) Connect and wire lamp leads, CD2, and CNSHfastener on circuit power source Assemble FEB3 and 4
case, and lock.as shown below.
CNPWRLock together.
Route CNBAR and #6800 through
fastener on ballast power source
case, and lock.
#6800
CN1WARNINGCP-S335(C9SM)/CP-X340, PJ552 (C9X)/CP-X345, PJ562 (C9XM)
CNBARFEB3
Surely tighten screw.
45~60 Crown
degreeswasher
FEB4
CNPOW
CD2
WARNINGSurely tighten screw.FEB3 FEB4
Power source
CD2caseTape lock portion.
CNSH
Route CD2 through hole in ZTP2 ZTP3
ZTP1 power source case, then
along the indentation in the
Secure CNSH at an angle of 45~60 degrees.
top of the case.
31Tape to case after routing.Securely lock the tabs on FEB3
and 4. Tape after locking. Be careful
of pinching the wires when closing
Lamp the ferrite core.
CNSHlead
Route CNPWR to pass between CNPOW
power source capacitor and case.When assembling control board
TSWRoute through power (1) Connect CNCT.
source case hole
TSWI/O metal
Control board
(back surface)
CD2EM01
CNCT
FEB4EV02EA01
CNPOW
Tape FEB3 and 4, and FEB3ET01
then secure with clamp.
Main board
put into the holes.
Wiring diagram 2 (C9SM/C9X/C9XM)