AV-32X37SUE AV-32X37HKE
AV-32X37HIE AV-32X35HUE
AV-32X35HKE AV-32H35SUE
2.3 DISASSEMBLY PROCEDURE
2.3.1 REMOVING THE REAR COVER2.3.8 CHECKING THE PW BOARD
(1) Unplug the power cord.? To check the back side of the PW Board.
(2) Remove the 13 screws [A] as shown in the Fig. 1. (1) Pull out the CHASSIS. (Refer to REMOVING THE
(3) Withdraw the REAR COVER toward you.CHASSIS).
(2) Erect the CHASSIS vertically so that you can easily check
the back side of the PW Board.
2.3.2 REMOVING THE SIDE CONTROL JACK ASSEMBLYCAUTION:
? Remove the REAR COVER.
? When erecting the CHASSIS, be careful so that there will be
(1) Remove the 1 screw [B] as shown in the Fig.1.
no contacting with other PW Board.
(2) While slightly raise the SIDE CONTROL JACK ASSY,? Before turning on power, make sure that the wire connector
remove the 2 claws under the SIDE CONTROL JACK ASSY.
is properly connected.
(3) Disconnect the connector [F] and [K] as shown in Fig. 2.? When conducting a check with power supplied, be sure to
confirm that the CRT EARTH WIRE (BRAIDED ASS?Y) is
connected to the CRT SOCKET PW board.
2.3.3 REMOVING THE SIDE CONTROL PWB
? Remove the REAR COVER.
? Remove the SIDE CONTROL JACK ASSY.
2.3.9 WIRE CLAMPING AND CABLE TYING
(1) Remove the 3 claws [C] from back side of the side control(1) Be sure to clamp the wire.
jack assembly as shown in Fig. 2.
(2) Never remove the cable tie used for tying the wires
(2) Pull out the SIDE CONTROL PWB.together.
Should it be inadvertently removed, be sure to tie the wires
with a new cable tie.
2.3.4 REMOVING THE CHASSIS
? Remove the REAR COVER.
(1) Slightly raise the both sides of the chassis by hand and
remove the 2 claws under the both sides of the CHASSIS
from the front cabinet.
(2) Withdraw the CHASSIS backward.
(If necessary, take off the wire clamp, connectors etc.)Connector
C
2.3.5 REMOVING THE POWER & DEF. PWB
? Remove the REAR COVER.
? Remove the CHASSIS.SIDE
(1) Remove the 3 screws [D] as shown in Fig. 1.CONTROLF
(2) Remove the POWER & DEF. PWB upper.PWB
(If necessary, take off the wire clamp, connectors etc.)K
C
2.3.6 REMOVING THE SIDE SPEAKER
(Back view)
? Remove the REAR COVER.
(1) Remove the 2 screws [E], and remove the SPEAKER
Fig.2
ADAPTER as shown in Fig. 1.
NOTE :
When removing the 2 screws [E] of the speaker holder
remove the lower side screw first, and then remove the
AV SW PWB
upper one.I
(2) Remove the 4 screws [F] attaching the SPEAKER.
AV
(3) Follow the same steps when removing the other handTERMINAL
SPEAKER.BOARD
2.3.7 REMOVING THE AV TERMINAL BOARD
? Remove the REAR COVER.
(1) Remove the 3 screws [G] as shown in the Fig. 1.
(2) Remove the 2 claws [H] under the CHASSIS as shown in
H
Fig. 3.
(3) Remove the AV TERMINAL BOARD slightly in the
direction of arrow [I] as shown in Fig. 3.
H
Fig.3
(No.52107)1-7 |
ACEC
