1.Torque driver10. INF adjustment lens
Be sure to use to fastening the mechanism and exte-To be used for adjustment of the camera system. For
rior parts because those parts must strictly be control-the usage of INF adjustment lens, refer to the Service
led for tightening torque.Bulletin No. YA-SB-10035.
2.Bit11. INF lens holder
This bit is slightly longer than those set in conventionalTo be used together with the camera stand (12) for op-
torque drivers.erating the Videocamera in the stripped-down condi-
tion such as the status without the exterior parts or for
3.Guide driver
using commodities that are not yet conformable to the
To be used to turn the guide roller to adjustment of the
interchangeable ring. For the usage of the INF lens
linearity of playback envelope.
holder, refer to the Service Bulletin No. YA-SB-10035.
4.Adjustment driver
12. Camera stand
To be used for adjustment.
To be used together with the INF adjustment lens
5.Jig connector cable
holder. For the usage of the Camera stand, refer to the
To be connected to the Jig connector jack of the main
Service Bulletin No. YA-SB-10035.
board and used for measurement and adjustment.
13. Light box assembly
MAINJIG CONN. BOARD
CN114 (PIN NO.) To be used for adjustment of the camera system. For
VF_RPD40 40VF_RPDthe usage of the Light box assembly, refer to the Serv-
CVF_G20 39CVF_R
ice Bulletin No. YA-SB-10035.
CVF_R39 38VF_COM
CVF_B19 37MT_G14. Gray scale chart (for Light box assembly)
VF_COM38 36MT_B
MT_RPD18 35MT_PSIGTo be used for adjustment of the camera system. For
MT_G37 33SBEthe usage of the Gray scale chart, refer to the Service
MT_R17 32FRP
MT_B36 31DISCRIBulletin No. YA-SB-10035.
MT_COMCS16 30ATFI
15. Color bar chart (for Light box assembly)
MT_PSIG35 29ENV_OUT
GND15 28TRSTTo be used for adjustment of the camera system. For
GND34 27TMS
the usage of the Color bar chart, refer to the Service
MONI_CHG14 26TDI
SBE33 25JLIP_TXBulletin No. YA-SB-10035.
SPA13 20CVF_G
FRP32 19CVF_B16. Cleaning cloth
FS_PLL12 18MT_RPDRecommended cleaning cloth to wipe down the video
DISCRI31 17MT_R
HID111 16MT_COMCSheads, mechanism (tape transport system), optical lens
ATFI30 15GNDsurface.
MAIN_VCO10 14MONI_CHG
ENV_OUT29 13SPA
PB_CLK9 12FS_PLL3.2 MECHANISM COMPATIBILITY ADJUSTMENT
TRST28 11HID1
TCMK8 10MAIN_VCONote:
TMS27 9PB_CLKWhen an adjustment is performed with the lower case cover
TDO7 8TCMK
TDI26 7TDOattached, first slide the Cover (M.ADJ) open and then per-
JLIP_RX6 6JLIP_RXform the compatibility adjustment.
JLIP_TX25
IF_TX5 Be sure not to damage the cover plate when sliding it open
AL_3VSYS24 to make an adjustment because it must be re-positioned af-
CJIG_RST4
VPPC23 ter completing the adjustment.
SRV_RX3
SRV_TX22 3.2.1 Jig connector cable connection
REG_3V2
DRST21 Remove one screw (1) first and the cover (JIG) next.
VPPD1
NOTE)
The JIG connector board uses 30 of the 40 pins of
CN114 on the Main board.
Pins 1 to 5, 21 to 24 and 34 of CN114 on the Main board
GUIDE ROLLER
are not used. (SUPPLY) ASSY
Fig. 3-1-3-1
COVER
(M.ADJ)
6.Communication cable1
Connect the Communication cable between the PC
COVER
cable and Jig connector cable when performing a PC
(JIG)
adjustment.
7.PC cable
To be used to connect the Videocamera and a personal
Jig Connector
computer with each other when a personal computer
GUIDE ROLLER
issued for adjustment. (TAKE-UP) ASSY
8.Alignment tapeJig connectorCommunication cable
Jig connector Oscilloscope
To be used for check and adjustment of interchange-
JLIP_RXTO ENV_OUT
REDwaveform
ability of the mechanism.
JLIP_TX
WHITEtriggerTO HID1
9.Service support system
GND
BLACK
To be used for adjustment with a personal computer.
Software can be downloaded also from JS-net.
Fig. 3-2-1-1
3-2 |
ACEC
