LG-GOLDSTAR FFH101 WL Repair Manual

$7.99

LG-GOLDSTAR FFH101 WL - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

Nadia Yakunina - 06/19/2007

It was so difficult to find this manual on the internet - thanks a lot for making it so easy and simple. Incredibly handy. AND. It looks you make so many people happy for such small money. Good job!

Dutra Lacerda - 02/17/2008

All schematics for the Euro-PC and some extra info. Needed if you want to replace some missing hardware. A piece of great historical value and for vintage computing entusiasts.

Roger Mason - 07/28/2006

Man, I was looking for this manual for a while! Where do You get them?;) Of course, quality is goooood:) Anyway, I can only say: A+A+A+!

Krzysztof Mazurek - 11/27/2007

Super ! Szukałem wszędzie i tutaj po 10 minutach miałem schemat w swoim PC.

Customers who bought this product also purchased

LG-GOLDSTAR 10214 Service Manual	LG-GOLDSTAR 1455D Service Manual	LG-GOLDSTAR 11225 Service Manual
LG-GOLDSTAR 1455DL Service Manual	LG-GOLDSTAR 1505S Service Manual	LG-GOLDSTAR 1423 Service Manual

Click to see text excerpt from the manual

10.2. INDOOR UNIT
10.2.1. SELECT THE BEST LOCATION10.2.3. TO DRILL A HOLE IN THEWALL
(Refer to OSelect the best locationÃ�AND INSTALL A SLEEVE OF
section)PIPING
1. Insert the piping sleeve to the hole.
10.2.2. HOW TO FIX INSTALLATION
2. Fix the bushing to the sleeve.
PLATE
3. Cut the sleeve until it extrudes about 15 mm froml.the wal
Caution
The mounting wall is strongsolidand enough to prevent it fromWhen the wall is hollow, please be sure to use the
the vibration.sleeve for tube ass?y to prevent dangers caused by
mice biting the indoor/outdoor connecting cable.
4. Finish by sealing the sleeve with puttyg or caulkin
compound at the final stage.
: Unit centre should be at more than 700 mm at right and left
of the wall.
The height should be more than 250 mm from the ceiling.
: From installation plate end to unit left side end is 55 mm.
: From installation plate end to unit right side end is 55 mm.
: Indoor outdoor connecting cable should be about 1100 mm
from this line. (Only for left rear piping)
1. Mount the installation plate on the wall with 6 screws10.2.4.. INDOOR UNIT INSTALLATION
(If mounting the unit on the concrete wall, consider using 1. For the right rear piping
anchor bolts.)
? Always mountthe installation platehorizontally by
aligning the marking-off line with the thread and using a
level gauge.
2. Drill the piping plate hole with o70 mm hole-core drill.
? Line according to the arrows marked on the lower left
and right side of the installation plate. The meeting point
of the extended line is the centre of the hole.
? Drill the piping hole at either the right or the left and the
hole should be slightly slant to the outdoor side.
2. For the right and right bottom piping
3. For the embedded piping