3-3
BRIEF OPERATING INSTRUCTIONS
English
11
DIGITAL
RECEIVER
CD PLAYER/RECORDER
LR
ANALOGINOUT
CD INDVD IN
InstallationsOUT
AUXIN
INOUTDIGITALOUT
OPTICALIN
OPTICAL
is displayed.
To disconnect the unit from the power
�
CLICK!OPTICAL IN
O
Digital optical connections via a digital receiver If you have a receiver with digital optical in- and outputs, these connections allow you to make digital recordings from various sources connected to the receiver.Remove the dust caps from the digital optical in- and outputs of the CD player/recorder and from the digital optical output of the receiver.Keep the caps in a safe place.Use a digital optical cable to connect the optical input of the receiver with OPTICALOUT on the CDplayer/recorder.Use another digital optical cable to connect the optical output of the receiver with OPTICALIN on the CD player/recorder.Make sure you insert the plugs fully,until a click is heard.Recording can be done now with any digital appliance connected to a digital input of the digital receiver (e.g. CDplayer or DVD player).Press INPUT on the CDplayer/recorder repeatedly to select the digital optical input.PowerThe type plate is located on the rear of the unit.Check whether the power voltage as shown on the type plate corresponds to your local power voltage.If it does not,consult your dealer or service organization.Make sure all connections have been made before switching on the power supply.Connect the power cable supplied to AC MAINS ~ and to the power outlet.This switches on the power supply.When the unit is switched to standby,it is still consuming some power.completely,remove the power plug from the power outlet.
120123
DIGITAL
CD PLAYERCD PLAYER/ RECORDERCD PLAYER/ RECORDERRECEIVER
CDR82x only
TLRLR
TPU
ANALOGINOUT
ANALOG OULR
OUT
COAXINANALOGINOUT
CD INDVD IN
DIGITALOUTOUT
DIGITAL OUTPUTOPTICALIN
OPTICALAUXIN
is displayed.INOUTDIGITALLis displayed.OUT
OPTICAIN
OPTICAL
�
CLICK!
OOPTICAL IN
DIGITAL IN
Direct digital optical connection This connection is required for direct recording from any digital audio equipment with a digital optical output (e.g. CD player or DVD player).Remove the dust caps from the digital optical input of the CD player/recorder and from the digital optical output of the external appliance.Keep the caps in a safe place.Use a digital optical cable to connect the optical output of the external appliance with OPTICALIN on the CDplayer/recorder.Make sure you insert both plugs fully, until a click is heard.Recording can be done now via the digital optical input. Press INPUT repeatedly on the CD player/recorder to select the digital optical input.Digital coaxial connections via a digital receiver If you have a receiver with digital coaxial in- and outputs, these connections allow you to make digital recordings from various sources connected to the receiver.Use a coaxial cable to connect the digital coaxial input of the receiver with DIGITALOUT on the CDplayer/recorder. Use another coaxial cable to connect the digital coaxial output of the receiver with DIGITALIN on the CDplayer/recorder.Recording can be done now with any digital appliance connected to a digital input of the digital receiver (e.g. CDplayer or DVD player).Press INPUT on the CDplayer/recorder repeatedly to select the digital coaxial input.
1200
CD PLAYERCD PLAYER/ RECORDER
LR
LR
ANALOGINOUT
ANALOG OUTPUT
OUT
COAXIN
DIGITALis displayed.OUT
DIGITAL OUTPUTOPTICALIN
OPTICAL
DIGITAL IN
How to connect if the analog output on the ampliŢer/receiver is already being used (occupied) Most ampliŢers/receivers have multiple analog output connections (TAPE,VCR,�),but some ampliŢers/receivers have only 1 analog output.In case you have already hooked up a tape deck (DAT recorder or MD recorder) to this output you will have to change the existing connections.Disconnect the analog connections from the tape deck to the ampliŢer/receiver.Connect the CD player/recorder (see steps 1�4 in the previous chapter).Connect the analog outputs of the tape deck to any free analog inputs (AUX,CD) on the ampliŢer/receiver: You can now playback your tape or record from your tape deck on CD.However,it is no longer possible to record on tape.Digital connectionsDirect digital coaxial connection This connection is required for direct recording from any digital audio equipment with a digital coaxial output (e.g. CD player or DVD player).Use a digital coaxial cable to connect the coaxial output of the external appliance with DIGITAL IN on the CDplayer/recorder:Recording can be done now via the digital coaxial input. Press INPUT on the CD player/recorder repeatedly to select the digital coaxial input.
1230
TURNTABLECD PLAYERAMPLIFIER/CD PLAYER/RECEIVERRECORDER
,TAPE OUT,
LRLRLRCDR/TAPE
INOUT
ANALOGINOUT
ANALOG OUTPUT
OUT
COAXINCDCD
LLRRDIGITALOUT
DIGITAL OUTPUTININININOPTICALis displayed.IN
PHONOOPTICALPHONO
ANALOG IN
Analog connectionsThese connections are required for playback and recording via an ampliŢer/receiver, equipped with analog in- andoutputs.Connect the red plug of the supplied audio cable (cinch) to the red jack ANALOG IN R and the white plug to the white jack ANALOG IN L on the CD player/recorde.r:Connect the other end of the audio cable to the analog outputs of the ampliŢer/receiver (CDR OUTAUX OUT,REC OUT,etc.).Connect the red plug of the supplied audio cable (cinch) to the red jack ANALOG OUT R and the white plug to the white jack ANALOG OUT L on the CD player/recorder:Connect the other end of the audio cable to the analog inputs of the ampliŢer/receiver (CD-R,TAPE IN,AUX, PLAYIN,etc.).Connect all other components of your system (tape deck, CD player,tuner,turntable,etc.) via their analog outputs to the appropriate analog inputs of the ampliŢer/receiver (CDIN,TUNER IN,AUX IN,PHONO IN,etc.).Recording can be done now withany appliance connected to an analog input of the ampliŢer/receiver:Press INPUT on the CD player/recorder repeatedly to select the analog input.
Installations12345010 |
ACEC
