YRD5023AU 04.7.30 11:23 AM Page 1
Connecting the Units<ENGLISH>
Note:
Y This unit is for vehicles with a 12-volt battery andY When this productOs source is switched ON, a con-
negative grounding. Before installing it in a recre-trol signal is output through the blue/white lead.
ational vehicle, truck or bus, check the batteryConnect to an external power ampOs system remote
voltage.control or the carOs Auto-antenna relay control ter-
Y To avoid shorts in the electrical system, be sure tominal (max. 300 mA 12 V DC). If the car features
MANUEL DOINSTALLATIONdisconnect the ` battery cable before beginninga glass antenna, connect to the antenna booster
installation.power supply terminal.
Y Refer to the ownerOs manual for details on con-Y When an external power amp is being used with
Power amp
necting the power amp and other units, then makethis system, be sure not to connect the blue/whiteThis Product
(sold separately)
connections correctly.lead to the ampOs power terminal. Likewise, do not
Y Secure the wiring with cable clamps or adhesiveconnect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tapeof the auto-antenna. Such connection could causeRear output
around them where they lie against metal parts.excessive current drain and malfunction.
DEH-3700MPJack for the Wired Remote ControlConnecting cords
Y Route and secure all wiring so it cannot touch anyY To avoid a short-circuit, cover the disconnected
Please see the Instruction Manual for thewith RCA pin plugs
moving parts, such as the gear shift, handbrake andlead with insulating tape. Insulate the unused
FuseWired Remote Control (sold separately).(sold separately)
seat rails. Do not route wiring in places that getspeaker leads without fail. There is a possibility of
Antenna jack
hot, such as near the heater outlet. If the insulationa short-circuit if the leads are not insulated.
of the wiring melts or gets torn, there is a danger ofY If this unit is installed in a vehicle that does notBlue/white
the wiring short-circuiting to the vehicle body.have an ACC (accessory) position on the ignition
To system control terminal of the power amp
Y DonOt pass the yellow lead through a hole into theswitch, the red lead of the unit should be connectedor Auto-antenna relay control terminal
engine compartment to connect to the battery. Thisto a terminal coupled with ignition switch ON/OFF
(max. 300 mA 12 V DC).
will damage the lead insulation and cause a veryoperations. If this is not done, the vehicle battery
dangerous short.may be drained when you are away from the vehi-
Y Do not shorten any leads. If you do, the protectioncle for several hours. (Fig. 1)
System remote control
circuit may fail to work when it should.
Yellow
Y Never feed power to other equipment by cutting
To terminal always supplied
the insulation of the power supply lead of the unitOACOC
FFNFFNwith power regardless of
and tapping into the lead. The current capacity ofOO
SSignition switch position.
the lead will be exceeded, causing overheating.TTAA
RR
Y When replacing the fuse, be sure to only use a fuseTT
WhiteGray
of the rating prescribed on this unit.Red
Y Since a unique BPTL circuit is employed, never++To electric terminal controlled
Front speakerFront speaker
wire so the speaker leads are directly grounded orby ignition switch (12 V DC)
ACC positionNo ACC position
the left and right ` speaker leads are common.ON/OFF.``
If you ground the products together and the groundWhite/blackGray/black
becomes detached, there is a risk of damage to theFig. 1LeftRight
This product conforms to CEMA cord colors.GreenViolet
products or fire.
Le code de couleur des c?bles utilisŽ pour ce produit estY The black lead is ground. Please ground this leadY Cords for this product and those for other prod-++Black (ground)
Rear speakerRear speaker
conforme ? CEMA.separately from the ground of high-current prod-To vehicle (metal) body.With a 2 speaker system, do not connect
ucts may be different colors even if they have the
``
Los colores de los cables este producto se conformanucts such as power amps.same function. When connecting this product toGreen/blackViolet/blackanything to the speaker leads that are not
If you ground the products together and the groundconnected to speakers.
con el c?digo de colores CEMA.another product, refer to the supplied manuals of
becomes detached, there is a risk of damage to theboth products and connect cords that have the
products or fire.
same function.
Y Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
Perform these connections when using++
ance of 4 to 8 ohms. Connecting speakers with out-
the optional amplifier.Rear speakerRear speaker
put and/or impedance values other than those
noted here may result in the speakers catching fire,``
emitting smoke, or becoming damaged.
INSTALLATION MANUAL
Fig. 2
Printed in China
ImprimŽ en Chine
<YRD5023-A/U> UC<KMMZX> <04H00000> |
ACEC
