DV-K303C
fonoitpircseD
LFDVDahtiwfisesuaCDCtauses ifw ith a CO peration ofthe Uni
rorrE
ID can notread
71An ID could notbe read for1 second orm ore.Stop
during tracing
Subcode check
No fram e could be read for3
72failure duringStop
seconds orm ore.
playback
ID can notread atAn ID could notbe read within 1 second afterOpens
73
the startupthe AFB adjustm enthad been finished.(ID readoutfailure)
No subcode could be read within 3
Subcode checkOpens (Subcode readout
74seconds afterAFB adjustm enthad
failure during startupfailure).
been finished.
Tim eoutforreading
TOC ofTOC readouttook 30 seconds or
81Stop
the m echanismm ore.
controller
Tim eoutforreading
Reading TOC ofthe system
82TOC ofthe systemStop
controllertook 30 seconds orm ore.
controller
Switching erroratClam ping could notbe com pleted during
97Retry clam p operation
currouselloadingloading.
Stop errorofCurrouseltray rotation could notbe com pleted
9AStop
currouseltraywithin 10 seconds.
Push errorof
9BPush in the tray from the loading tray open state.Close the tray
currouseltray
PullerrorofPulloutthe tray from the loading tray close
9COpen the tray
currouseltraystate.
Stop errorof
Loading tray m ovem entcould notbe com pleted
9DcurrouselloadingOpen the tray
within 10 seconds.
tray
Stop (Initialize the
Abnorm alerrorofTray switch errorwas detected with the
9Em echanism in the
currouselswitchcurrouseltray.
m echanism controller.)
Turn offthe power
CurrouselinitializeInitialization could notbe achieved with theinstantly (no indication on
9F
errorcurrouseltray.the FL display and no
writing to flash m em ory.)
A com m and could notbe issued to DSP
Com m unication
because Com m and Busy (XCBUSY)was in
A1tim eoutofDSPNo operation
force (XCBUSY = L)fora specified tim e (about
com m and
200 ?S).
Com m and Busy (XCBUSY)was in force fora
Com m unicationspecified tim e (about200 ?S)before and aftera
A2tim eoutforreadingcoefficientread com m and was issued to DSP,orNo operation
DSP coefficientthe address echo-back aftercom m and issuance
did notm atch the setup address.
Com m and Busy (XCBUSY)was in force fora
Com m unication
specified tim e (about1024 m S)before and after
A3tim eoutforwritingNo operation
the coefficientwrite com m and was issued to
DSP coefficient
DSP.
Com m unicationCom m and Busy (XCBUSY)was in force for200
tim eoutfor?S during continuous coefficientwriting,or
A4No operation
continuously writingbefore and aftera continuous write com m and
DSP coefficientwas issued to DSP.
In the tracing state during the backup sequence,codes could notbe read for1
Tim eouterrorforsecond orm ore.
B1Stops
backupIn the backup sequence,tracking ON sequence ofthe servo DSP could notbe
com pleted even ifm ore than 500 m S afterthe tracking ON com m and was issued.
Retry errorfor
B2Tracing im possible afterretring the tracking ON for3 tim es in the backup sequence. Stops
backup
During tracing,runaway was detected afterthree iterations ofbackup operations for
Be3 Retry errorfortracStops
detecting runaway.
Stops (the m echanical
Detection oftrackingDuring playback,the overcurrentdetection portwas atL for300 m s orm ore
C3controlleroperates
overcurrentcontinuously.
independently).
52 |
ACEC
