21A2-X 14A2-X
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
NO. Adjustment partAdjusting procedure and conditionsWaveform and others(Continued)
1CONTRAST1. Receive "Monoscope Pattern" signal.NO. Adjustment partAdjusting procedure and conditionsWaveform and others
key2. Set P-Mode to select CONTRAST.
3. Press Volume Up/Down key to check whether9Colour1. Receive the "PAL COLOUR BAR" signal, press
the CONTRAST effect is OK or not.systemthe COLOUR SYSTEM key to select modes
except PAL, check the COLOUR is not working
properly. Then, select the "PAL" mode. Check
2COLOUR key1. Receive "Colour Bar" signal.again its colour so that it is working properly.
2. Set P-Mode to select COLOUR.2. Receive "SECAM COLOUR BAR" signal,
3. Press Volume Up/Down key to check whetherpress COLOUR SYSTEM key to select modes
the COLOUR effect is OK or not.except SECAM, check the COLOUR is not
working properly. Then, select the "SECAM"
mode. Check again its colour so that it is
3BRIGHTNESS1. Receive "Monoscope Pattern" signal.working properly.
key2. Set P-Mode to select BRIGHTNESS.3. Receive "NTSC 4.43/3.58 COLOUR BAR" sig-
3. Press Volume Up/Down key to check whethernal thru AV, press COLOUR SYSTEM key to
the BRIGHTNESS effect is OK or notselect modes except N4.43/3.58, check the
COLOUR is not working properly. Then, select
4TINT key1. Receive the "NTSC Colour Bar" signal thru AVthe "NTSC 4.43/3.58" mode. Check again its
colour so that it is working properly.
in.
2. Set P-Mode to select TINT.10 Sound1. Receive "PAL-D/K" signal, press the "SOUND
3. Press Volume Up/Down key to check TINT, UPsystemSYSTEM" to select B/G and I. Check the sound
for GREEN direction and DOWN for PURPLEoutput is not working properly. Select D/K and
direction whether is OK or not.check the sound output to make sure it is
working properly.
5SHARPNESS1. Receive "Monoscope Pattern" signal.2. Receive "PAL-I" signal, press the "SOUND
SYSTEM" to select B/G and D/K. Check the
Key2. Set P-mode to select SHARPNESS.
sound output is not working properly. Select I
3. Press Volume Up/Down key to check whether
10and check the sound output to make sure it is
the SHARPNESS effect is OK or not.
working properly.
3. Receive "PAL-B/G" signal, press the "SOUND
SYSTEM" to select I and D/K. Check the sound
6CH DISPLAY1. All Ch (1~99) will have an OSD display of theoutput is not working properly. Select B/G and
COLOURchannel number in green colour under AFT ONcheck the sound output to make sure it is
condition.working properly.
4. Receive "NTSC-M" signal thru AV, press the
"SOUND SYSTEM" to select B/G, D/K and I,
7NORMAL Key1. Once in PICTURE Mode, and the NORMALNote:If nothing is display meancheck the sound output is not working properly.
key is pressed, all the settings will be presentcontrast, colour, bright, tintSelect M and check the sound output to make
to normal setting.or sharpness are all in nor-sure it is working properly.
(Normal setting value for every mode).mal setting.
11 NOISE MUTE1. Receive "PAL COLOUR BAR" signal.
? CONTRAST: MAXCHECKING2. Turn up the volume control to maximum, make
? COLOUR: CENTERsure the sound is heard from the speakers.
? BRIGHTNESS : CENTERThen put the unit in no signal state.
3. Check the sound mute is effective.
? TINT: CENTER
4. Finally turn sound level of CTV to minimum.
? SHARPNESS : CENTER
12 OSDCheck OSD LANGUAGE quantity and type for
8White Temp1. Receive "Monoscope Pattern" signal.LANGUAGErespect model.
2. Set FUNCTION to select WHITE TEMP.QUANTITYModel QuantityEnglish RussianChinese French Arabic Malay
3. Press Volume Up/Down key to check WHITECHECKA3OXOXXO
TEMP Option, STANDARD:B3OXOXXO
NORMAL SETTING, WARM for moreC3OXOXXO
REDDISH direction changing, COOL for moreE4OOXOOX
F5OXOOOO
BLUISH direction changing.
G5OX OOOO
J2OOXXXX
10-110-2 |