14D1-SA/SF/GA/GF
14D2-SA/SF/GA/GF
????????????
SUB ADJ.ADJ.ADJ.SUB ADJ.
MODEMODEMODEMODE
Y-DELAYOFFSET
SUB TINT (SUB-TINT)FORWARD : CH DOWN KEY REVERSE : CH UP KEY
MAX VOLUME (SUB-VOL)SUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)SUB BRIGHTNESS (SUB-BRI)SUB SHARPNESS (SUB-SHP)MAX HOTEL VOLUME (HTL-VOL)HOTEL PROGRAM NO(HTL-PRG)OSD GRB REFERENCE (RGB)BLACK LEVEL OFFSET R(CUT-R)BLACK LEVEL OFFSET B(CUT-B)CATHODE DRIVE LEVEL(CDL)
IC?????????
ADJ. MODEMODEADJ.3-2MODE
OPTION
WHITE POINTWHITE POINT
W.P RED STD. W.T. (DRI-RS)W.P.BLUE STD. W.P. (DRI-BS)W.P. RED COOL W.P.(DRI-RW)
W.P. GREEN STD. W.T.(DRI-GS)W.P. RED WARM W.P.(DRI-RC)W.P. BLUE WARM W.P.(DRI-BC)W.P. BLUE COOL W.P. (DRI-BW)
W.P. GREEN WARM W.P.(DRI-GC)W.P. GREEN COOL W.P.(DRI-GW)
?????????????
AGC &MODEMISC. OPTION MODEAGC &MODE
GEOMETRICGEOMETRIC
SERVICE MODE
HORIZONTAL BOW (HB)
VERTICAL SLOPE (V-LIN) VERTICAL AMP (V-AMP) VERTICAL SHIFT (V-CENT)S-CORRECTION (S-COR)
(1)In the Service Mode, Key is used to select the mode in the following order.AGC TAKE OVER POINT (AGC) HORIZONTAL SHIFT (H-CENT) EAST-WEST WIDTH (H-SIZE)HORIZONTAL PARALLELOGRAM (EW//)EAST-WEST PARABOLA/WIDTH (PARA)EAST-WEST UPPER COR. PB (COR(U))EAST-WEST LOWER COR. PB (COR(L))EAST-WEST TRAPEZIUM (TRAPE)FORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display.
2C bus control and in the conventional
2C bus control).
3-1
2C bus control include preset-only items and variable data.
above).
11111
ADJUSTMENT PRECAUTIONS
microprocessor is in input mode. (Adjustment through the Imicroprocessor is in out of the service mode.position.Initial values are automatically preset, only when a new EEPROM is used (Judge with the first 4 bytes ).
. Short JA 137 & JA 138 for 1 second and release to switch to the service mode position, and the. Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.. Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.. Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.. Short JA 137 & JA 138 for 1 second and release to switch to the normal mode position, and the.Short JA 137 & JA 138 then turn "ON" the main power and release to switch to the Service Mode. The initial data are preset as listed in page 5.. Make sure the data need modification or not (Initial data).
12345123Once the chassis has been assembly together and ready to be POWER ON for the FIRST TIME, make sure to short JA137 & JA138 to switch to the service mode position first and then turn on the main power switch (See 2-Precaution: If haven't done this initialization, it may possibly generate excessive Beam current.
(GA-1AM Series type RH-IX3368CE Attachment)
This model's setting are adjusted in two different ways: through the Ianalog manner. The adjustments via the ICAUTION: Make sure TV Set is in "Normal Condition" before switch to Service Mode for adjustment.1. Setting the service mode by the microprocessor.2.Factory Presetting.Note:3.For reference please check with memory map
3 |