14U10/15
14U20/25
????????????
SUB ADJ.ADJ.ADJ.SUB ADJ.MODEMODEMODEMODE
Y-DELAYOFFSET
SUB TINT (SUB-TINT)
FORWARD : CH DOWN KEY REVERSE : CH UP KEY
MAX VOLUME (SUB-VOL)SUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)SUB BRIGHTNESS (SUB-BRI)SUB SHARPNESS (SUB-SHP)OSD GRB REFERENCE (RGB)CATHODE DRIVE LEVEL(CDL)
MAX HOTEL VOLUME (HTL-VOL)HOTEL PROGRAM NO(HTL-PRG)BLACK LEVEL OFFSET R(CUT-R)BLACK LEVEL OFFSET G(CUT-G)
ollowing order.
IC?????????
ADJ.MODEMODEMODE3-2ADJ.
OPTION
WHITE POINTWHITE POINT
W.P. RED STD. W.T. (DRI-RS)W.P. BLUE STD. W.P. (DRI-BS)W.P. RED COOL W.P.(DRI-RC)
W.P. GREEN STD. W.T.(DRI-GS)W.P. BLUE COOL W.P. (DRI-BC)W.P. RED WARM W.P.(DRI-RW)W.P. BLUE WARM W.P.(DRI-BW)
W.P. GREEN COOL W.P.(DRI-GC)W.P. GREEN WARM W.P.(DRI-GW)
??????
AGC &MODEMISC. OPTION MODEAGC &MODE
GEOMETRICGEOMETRIC
SERVICE MODE VERTICAL AMP (V-AMP)
VERTICAL SLOPE (V-LIN) VERTICAL SHIFT (V-CENT) S-CORRECTION (S-COR)
(1)In the Service Mode, Key is used to select the mode in the fAGC TAKE OVER POINT (AGC) HORIZONTAL SHIFT (H-CENT) FORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD display.
y one.
n on the
ventional
versibly one by one.
ariable data.
w EEPROM is used (Judge
2C bus control and in the con2C bus control). (Use JWS Key to set as, the data can be modified.
witch to the service mode position, and the
witch to the normal mode (OFF) position, and thewitch to the service mode position and tur
3-1
hment)
vice mode.ly together and ready to be POWER ON for the FIRST TIME,
. (Adjustment through the I
2C bus control include preset-only items and v
o different ways: through the I
above).
1
WN / UP key on the remote controller to get ready to select the mode one bWN / UP key on the remote controller to select the modes re
ADJUSTMENT PRECAUTIONS
vice mode by the microprocessor.
microprocessor is in input modewell).microprocessor is in out of the sermain power switch. Initial values are automatically preset, only when a newith the first 4 bytes ).
. Short JA 122 & JA 124 for 1 second and release to s. Press the CH DO. Press the CH DO. Using the VOLUME UP/ DOWN key on the remote controller. Short JA 122 & JA 124 for 1 second and release to s.Short JA 122 & JA 124 for 1 second and release to s.The initial data are preset as listed in page 5, & 6..Make sure the data need modify or not (Initial data).
12345123make sure to short JA122 & JA124 to switch to the service mode position first and then turn on the main power switch (See 2-Precaution: If haven't done this initiation, it may possibly generate excessive Beam current.
(UA1 Series type RH-iX3368CE Attac
This model's setting are adjusted in twanalog manner. The adjustments via the I1. Setting the ser2.Factory Presetting.Note:Once the chassis has been assemb3.For reference please check with memory map
3 |
ACEC
