20D2-S/G
21D1-S/G
21D2-S/G
-R)-B)
OL)
????????????
SUB ADJ.ADJ.ADJ.SUB ADJ.
MODEMODEMODEMODE
Y-DELAYOFFSET
SUB TINT (SUB-TINT)
FORWARD : CH DOWN KEY REVERSE : CH UP KEY
MAX VOLUME (SUB-VSUB COLOUR (SUB-COL)
SUB CONTRAST (SUB-CON)SUB BRIGHTNESS (SUB-BRI)SUB SHARPNESS (SUB-SHP)MAX HOTEL VOLUME (HTL-VOL)HOTEL PROGRAM NO(HTL-PRG)OSD RGB REFERENCE (RGB)BLACK LEVEL OFFSET R(CUTBLACK LEVEL OFFSET B(CUTCATHODE DRIVE LEVEL(CDL)
W.T.(DRI-GW)
IC?????????3-2.
ADJ.ADJ.
MODEMODEMODE
OPTION
WHITE POINTWHITE POINT
W.P RED STD. W.T. (DRI-RS)W.P.BLUE STD. W.T. (DRI-BS)W.P. RED COOL W.T.(DRI-RW)
W.P. GREEN STD. W.T.(DRI-GS)W.P. RED WARM W.T.(DRI-RC)W.P. BLUE WARM W.T.(DRI-BC)W.P. BLUE COOL W.T. (DRI-BW)
W.P. GREEN WARM W.T.(DRI-GC)W.P. GREEN COOL
ARA)y.
-LIN)
PB (LOR(U))
?????????????
AGC &MODEMISC. OPTION MODEAGC &MODE
GEOMETRICGEOMETRIC
SERVICE MODE
HORIZONTAL BOW (HB)
VERTICAL SLOPE (V VERTICAL AMP (V-AMP) VERTICAL SHIFT (V-CENT)S-CORRECTION (S-COR)
(1)In the Service Mode, Key is used to select the mode in the following orderAGC TAKE OVER POINT (AGC) HORIZONTAL SHIFT (H-CENT) EAST-WEST WIDTH (H-SIZE)HORIZONTAL PARALLELOGRAM (EW//)EAST-WEST PARABOLA/WIDTH (PEAST-WEST UPPER COR.EAST-WEST LOWER COR. PB (COR(L))EAST-WEST TRAPEZIUM (TRAPE)FORWARD : CH DOWN KEY REVERSE : CH UP KEY * ( ) means OSD displa
with the first 4 bytes ).
2C bus control and in the conventional
PRECAUTIONS3-1
2C bus control include preset-only items and variable data.N6)
is in input mode. (Adjustment through the I2C bus control). (Use JWS Key to set as
ADJUSTMENT is in out of the service mode.
. Short JA 137 & JA 138 for 1 second and release to switch to the service mode position, and the microprocessor well).. Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.. Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.. Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.. Short JA 137 & JA 138 for 1 second and release to switch to the normal mode (OFF) position, and the microprocessor . Short JA 137 & JA 138, then turn on the main power and release to switch to the Service Mode position. Initial values are automatically preset, only when a new EEPROM is used (Judge. The initial data are preset as listed in page 8, 9, & 10.. Make sure the data need modify or not (Initial data).
12345123Once the chassis has been assembly together and ready to be POWER ON for the FIRST TIME, make sure to short JA137 & JA138 to switch to the service mode position first and then turn on the main power switch (See 2-(1) above).Precaution: If haven't done this initiation, it may possibly generate excessive Beam current.
(GA-1 Series type RH-iX3368CE
This model's setting are adjusted in two different ways: through the Ianalog manner. The adjustments via the ICAUTION: Make sure TV set is in "Normal condition" before switch to Service Mode for adjustment.1. Setting the service mode by the microprocessor.2.Factory Presetting.Note:3.For reference please check with memory map
3 |
ACEC
