14D2-SS
20D2-SS
21D2-SS
veform orothers
Wa
mean contrast, colour, bright, tint, sharpness are all in nor- mal setting.
Notes:If nothing is display
10-2
(Continued)
CONTRAST: MAX COLOUR: CENTER BRIGHTNESS: CENTER TINT: CENTER SHARPNESS: CENTER
Once in PICTURE Mode, and theNORMAL key is pressed, all the settings will be present to nor- mal setting. (Normal setting value for every mode).? ? ? ? ?Press Volume Up/Down key to check WHITE TEMP Option, STANDARD: NORMAL SETTING, WARM for more REDDISH direction changing, COOL for more BLUISH di- rection changing.Receive the "PAL COLOUR BAR" signal, press the COLOUR SYSTEM key to select modes ex- cept PAL, check the COLOUR is not working prop- erly. Then, select the "PAL" mode. Check again its colour so that it is working properly.Receive "SECAM COLOUR BAR" signal, press COLOUR SYSTEM key to select modes except SECAM, check the COLOUR is not working prop- erly. Then, select the "SECAM" mode. Check again its colour so that it is working properly.Receive "NTSC 4.43" signal, press COLOUR SYSTEM key to select modes except NTSC 4.43, check the COLOUR is not working properly. Then, select the "NTSC 4.43" mode. Check again its colour so that it is working properly.Receive "NTSC 4.43/3.58 COLOUR BAR" signal thru AV, press COLOUR SYSTEM key to select modes except N4.43/3.58, check the COLOUR is not working properly. Then, select the "NTSC 4.43/3.58" mode. Check again its colour so that it is workingproperly.
1.1.Receive "Monoscope Pattern" signal. 2.Set FUNCTION to select WHITE TEMP. 3.1.2.3.4.
NORMAL KeyWHITE TEMPCOLOUR SYSTEM
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)No.Adjusting pointAdjusting procedure/conditions789
veform orothersveform orothers
WaWa
10-1
reen colour under AFT ON
3 dB).
?
Make sure the O/P is as specified
3 dB).
Make sure the output is as specified (1.0?
rminate the Video output with a 75 ohm imped-rminate the Audio output with a 10k ohm im- & TV again and the video & audio output are
Colour Bar, Sound 400 Hz 100% Mod).Teance. Vp-p Tepedance. (1.76 Vp-p Using the TV/AV key on the remote controller, make sure that the modes change in order of TV, AVaccording to the input terminal for each mode. If connect input to Front and Rear AV terminal, in- put terminal of Front AV will be selected.Press Volume Up/Down key to check whether the CONTRAST effect is OK or not.Press Volume Up/Down key to check whether the COLOUR effect is OK or not.Press Volume Up/Down key to check whether the BRIGHTNESS effect is OK or not.Receive the "NTSC Colour Bar" signal thru AV in.Press Volume Up/Down key to check TINT, UP for GREEN direction and DOWN for PURPLE di- rection whether is OK or not.Press Volume Up/Down key to check whether the SHARPNESS effect is OK or not.All Ch (1~99) will have an OSD display of the channel number in gcondition.
1.Receive the "PAL Colour Bar" signal (100% White2.3.1.1.Receive "Monoscope Pattern" signal. 2.Set P-Mode to select CONTRAST. 3.1.Receive "Colour Bar" signal. 2.Set P-Mode to select COLOUR. 3.1.Receive "Monoscope Pattern" signal. 2.Set P-Mode to select BRIGHTNESS. 3.1.2.Set P-Mode to select TINT. 3.1.Receive "Monoscope Pattern" signal. 2.Set P-mode to select SHARPNESS. 3.1.
A/V INPUT AND OUTPUT CHECKING
VIDEO AND AUDIO OUTPUT CHECKVIDEO AND AUDIO INPUT CHECKCONTRAST keyCOLOUR keyBRIGHTNESS keyTINT keySHARPNESS KeyCH DISPLAY COLOUR
12123456
No.Adjusting pointAdjusting procedure/conditionsFUNCTION OPERATION CHECKING (VIDEO AND AUDIO)No.Adjusting pointAdjusting procedure/conditions
10 |
ACEC
