SHARP 29HFD5RU Repair Manual

$7.99

SHARP 29HFD5RU - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

vedat kaya - 07/18/2008

i got my service manual for philips vr685-02. Thanks a lot for my very clear and net service manual. I will continue shopping from user-manual.com.

matt wilschke - 03/07/2008

Essential for popping the top open and cleaning and replacing what needs repalced. One note: the Ornamental Panel is attached with some adhesive as well as screws and faders so don't be shy about prying it open.

Jason Gaunt - 01/26/2008

This manual is for both the EU and Australian version of the CCD-TR55(E) Camcorder, as stated it includes both the users manual and the service manual. The quality of the manual is very good but it is only black and white (not full colour) and ultimately it is just a scan, so 4/5 from me.

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

Carl Conti - 08/03/2006

Thanks for manual for Luxman M02. I'll recomend this site to my friends for sure! Keep on the good work!

Customers who bought this product also purchased

SHARP 115U_OM.pdf Service Manual	SHARP 10P28G Service Manual	SHARP 14BN14 Service Manual
SHARP 10P35G Service Manual	SHARP 14BN1A Service Manual	SHARP 10P18G Service Manual

Click to see text excerpt from the manual

29H-FD5RU
R
MgB
G
00% W -
CyGBCy
YMgRFig Same Level
Y
W
75% W
-
(W and Mg same
58 Colour Bar" signal15-2
(AC)(Use Probe 0: )
CHROMA ADJUSTMENT
Adjust the "SUB-TINT" data to obtain the
L
Adjustment conditions/procedureWaveform or remarksAdjustment conditions/procedureWaveform or remarksAdjustment conditions/procedureWaveform or remarks
Range :2 V/Div Sweep Time :20 ?sec/Div
PA Range: 00mV/Div Sweep time: 0 ?sec/Div
ler.( Use Probe 10:1)mote controller, and vary the sub color data to make 00% W of the color bar and RED at the same level for adjustment shown in Fig NTSC CHROMA ADJUSTMENTReceive the "NTSC 3 through AV IN BLUE-OUT ??Select the "SUB-TINT" item in the ADJUSTMENT MODE waveform shown as Figure level)
Align the center of the screen to the geometric center of CRT (monoscope)Align the center of the screen to the geometric center of CRT (monoscope)NOTE : There are no separate adjustment for 16:9 mode and Normal mode adjustment. The 16:9 (Panorama mode 50/60Hz) data need to follow the adjusted data for Normal mode (50/ 60Hz). Please set the data as below.VER-AMP-P50 = VER-AMP-N50 VER-SHI-P50 = VER-SHI-N50 HOR-SHI-P50 = HOR-SHI-N50 EW-W-P50 = EW-W-N50 VER-AMP-P60 = VER-AMP-N60 VER-SHI-P60 = VER-SHI-N60 HOR-SHI-P60 = HOR-SHI-N60 EW-W-P60 = EW-W-N601.Receive the "PAL Color Bar" signal. 2.Make the image normal with the remote control-3.Connect the oscilloscope to TP48R (IC851 #9).4 Set the sub color adjustment mode with the re- 2 Connect the oscilloscope to TP47B (P860 Pin6)3
2C BUS2C BUS
Adjustment pointVHOR-SHI-N60EW-W-N60Adjustment pointSUB COLOUR (ICONTROL)Adjustment pointSUB-TINT ( ICONTROL)
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT11
No.No.No.
D2D1
W
AR
Fig. 1-2Fig. 1-3Fig. 1-4Fig. 1-5H-PFig. 1-6H-BO
Fig. 1-7
A B CA : Out of spec B : OK C : Out of spec
15-1
so that the middle 4 blocks are

Adjustment conditions/procedureWaveform or remarks
Adjust V-Slope by Volume Up / Down Remote Control. Refer to Fig. 1.1.(monoscope)Adjust the overscan to 8.5%. (monoscope)Align the center of the screen to the geometric center of CRT. (monoscope)Align the center of the screen to the geometric center of CRT.(monoscope)Adjust the overscan to 8.5%. (monoscope)Adjust the linearity to the best. (monoscope)Already preset.(Adjust this unless the linearity is achieved.)(monoscope)Already preset..Already preset .Adjust the 2nd vertical line from the end of the crosshatch pattern. Refer to Fig 1.6.(crosshatch)Adjust the 2nd vertical line from the end of the crosshatch pattern. Refer to Fig 1.7.(crosshatch)Adjust the 2nd vertical line from the right end of the crosshatch patternstraight. Refer to Fig 1-2.(crosshatch)Adjust the 2nd upper vertical line from the right end of the crosshatch pattern so that the upper line are straight. Refer to Fig 1-3.(crosshatch)Adjust the 2nd lower vertical line from the right end of the crosshatch pattern so that the bottom line are straight. Refer to Fig 1-4.(crosshatch)Adjust the 2nd vertical line from the right end of the crosshatch pattern so that the D1 (center area of the second vertical line - edge of screen) and D2 (top area of the second vertical line - edge of screen) are same. Refer to Fig 1-5.(crosshatch)Adjust the overscan to 10%.(monoscope)Align the center of the screen to the geometric center of CRT.(monoscope)
S CORRSCROLL
-SLOPE-LINE
Adjustment pointMAIN SCREEN ADJUSTMENTVVER-AMP-N50VER-SHI-N50HOR-SHI-N50EW-W-N50VV-V-VX-NORMALH-PARH-BOWE/W-PARUPCOR-PARLOCOR-PAREW-TRAPVER-AMP-N60VER-SHI-N60
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENTNo.1
15