29H-FG3RU
17-2
service mode and choose "Setting Mode 1". Key in the alphabic number 114 to enter GAME-HON. Adjust to the proper horizontal position.same "Setting Mode 1". Key in the alphabic number 115 to enter GAME- VERT-1. Adjust to the proper vertical position.
Adjustment conditions/procedureWaveform or remarks(B) For the VERTICAL position, remain inAdjustment conditions/procedureWaveform or remarks
GAME OPERATION CHECK
Mode.key to enter "The Rock" game), and then confirm the position and the function of the game.key to exit to previously viewed channel from the game mode.89.5 MHz with sound modulation 400Hz.the RF coaxial cable with female adaptor.the FM RADIO menu.VOL+ key to search the frequency of 89.5 MHz.
FM RADIO OPERATION CHECK
1.Use the "GAME" key (R/C) to enter the Game2.Press the TREBLE UP (code=46H) key (directNote : (A) For the HORIZONTAL position, enter3. If adjustment OK, then press the "GAME MODE"1.Use the signal generator to set carier frequncy of2.Connect the signal to the FM radio tuner using3. Press the "FM RADIO" button of R/C to access4.Select the "FREQUENCY" in menu and press the5. Confirm the 400 Hz audio is clearly detected. 6. Press the "FM RADIO" button of R/C to exit.
Adjustment point( For models with GAME only.)Adjustment point( For models with RADIO only.)
11
No.No.
R
MgB
G
00% W
CyGBCy
YMgRFig -Same Level
Y
W
75% W
17-1
CHROMA ADJUSTMENT
L
Adjustment conditions/procedureWaveform or remarksAdjustment conditions/procedureWaveform or remarksAdjustment conditions/procedureWaveform or remarks
Range :2 V/Div Sweep Time :20 ?sec/Div
PA Range: 00mV/Div (AC)(Use Probe 0:)Sweep time: 0 ?sec/Div
ler.( Use Probe 10:1)Set the sub color adjustment mode with the re- mote controller, and vary the sub color data to make 00% W of the color bar and RED at the same level for adjustment shown in Fig -NTSC CHROMA ADJUSTMENTReceive the "NTSC 358 Colour Bar" signal through AV INConnect the oscilloscope to TP47B (P860 Pin6) BLUE-OUT ??Select the "SUB-TINT" item in the ADJUSTMENT MODE Adjust the "SUB-TINT" data to obtain the waveform shown as Figure (W and Mg same level)
Align the center of the screen to the geometric center of CRT(monoscope)Align the center of the screen to the geometric center of CRT(monoscope)NOTE : There are no separate adjustment for 16:9 mode and Normal mode adjustment. The 16:9 (Panorama mode 50/60Hz) data need to follow the adjusted data for Normal mode (50/ 60Hz). Please set the data as below.VER-AMP-P50 = VER-AMP-N50 VER-SHI-P50 = VER-SHI-N50 HOR-SHI-P50 = HOR-SHI-N50 EW-W-P50 = EW-W-N50 VER-AMP-P60 = VER-AMP-N60 VER-SHI-P60 = VER-SHI-N60 HOR-SHI-P60 = HOR-SHI-N60 EW-W-P60 = EW-W-N601.Receive the "PAL Color Bar" signal. 2.Make the image normal with the remote control-3.Connect the oscilloscope to TP48R (IC851 #9).423
2C BUS2C BUS
Adjustment pointVHOR-SHI-N60EW-W-N60Adjustment pointSUB COLOUR (ICONTROL)Adjustment pointSUB-TINT ( ICONTROL)
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENTNo.No.1No.1
17 |
ACEC
