29R600P
WAVEFORM OR OTHERS
SETTING CONDITION
signal.PICTURE control setting with R/C, select the CONTRAST.by using the VOLUME UP / DOWN key.or not.signal.PICTURE control setting with the R/C, select the COLOUR.using the VOLUME UP / DOWN key.not.signal.PICTURE control setting with the R/C, select the BRIGHTNESS .BRIGHTNESS by using the VOLUME UP / DOWN key.or not.PATTERN" signal.PICTURE control setting with the R/C, select the TINT.the VOLUME UP/DOWN key.signal.PICTURE control setting with the R/C, select the SHARPNESS.by using the VOLUME UP / DOWN key.or not.
1.Receive the "MONOSCOPE PATTERN" 2.Press the CH UP/DOWN key for 3.Increase or decrease the CONTRAST 4.Check whether the CONTRAST is OK 1.Receive the "COLOUR BAR PATTERN" 2.Press the CH UP / DOWN key for 3.Increase or decrease the COLOUR by 4.Check whether the COLOUR is OK or 1.Receive the "MONOSCOPE PATTERN" 2.Press the CH UP / DOWN key for 3.Increase or decrease the 4.Check whether the BRIGHTNESS is OK 1.Receive the "NTSC COLOUR BAR 2.Press the CH UP/DOWN key for 3.Increase or decrease the TINT by using 4.Check whether the TINT is OK or not. 1.Receive the "MONOSCOPE PATTERN" 2.Press the CH UP / DOWN key for 3.Increase or decrease the SHARPNESS 4.Check whether the SHARPNESS is OK
CHECKING POINT
CHECKING OPERATION (VIDEO & AUDIO)
1CONTRAST2COLOUR3BRIGHTNESS4TINT5SHARPNESS
NO
WAVEFORM OR OTHERSWAVEFORM OR OTHERSWAVEFORM OR OTHERS
3 dB) when volume max. 3 dB)? 3 dB).
??
% White Colour Bar Sound 400 Hz 100 %Mod)Kohm impendence Make sure the O/P is as specified (0.9 Vp-p White Color Bar Sound 400 Hz 100% Modulation)impendence. Make sure the output is as specified (1.0 Vp-p impendence. Make sure the O/P is as specified (1.76 Vp-p make sure that the modes change in order of TV, AV1, AV2 & TV again and that the video & audio outputare according to the input terminal for each mode.AUTO SELECT mode, use thevolume up/ down key to switch "ON" the AUTO SELECT.channel will switch from other channel to AV2 automatically.SELECT.signal.ground, make sure the protector ON and switch to standby mode.signal.cathode (D608).sure the protector is work.short testing in + B line, check all possible damaged components on +B line.
ADJUSTMENT CONDITION/PROCEDURE
1.Receive the "PAL COLOUR BAR" signal (100 2.Terminate the sub-woofer output with a 10ADJUSTMENT CONDITION/PROCEDURE 1.Receive the "PAL COLOUR BAR" signal(100 % 2.Terminate the Video output with a 75 ohm 3.Terminate the Audio output with a 10 Kohm 1.Using the TV/AV key on the remote controller, 1.Press the remote control "FUCTION" key until 2.Connect Video signal to FRONT AV(AV2), the 3.After checking please "OFF" the AUTOADJUSTMENT CONDITION/PROCEDURE 1.Receive the "MONOSCOPE PATTERN" 2.Set CONTRAST MAX. 3.Set BRIGHT MAX. 4.While the R or B or G Cathode short to 1.Receive the "MONOSCOPE PATTERN" 2.Connect output of Bias Box to D601 3.Set voltage of Bias Box to 20V and make 1.Once finish rectified Electrolytic Capacitor
ADJUSTMENT POINTTERMINATERADJUSTMENT POINTOUTPUT CHECKINGINPUT CHECKINGADJUSTMENT POINTBEAM PROTECTOROTHER PROTECTOR
SUB WOOFER TERMINATE CHECKINGA/V INPUT/OUTPUT CHECKINGPROTECTOR OPERATION CHECKING
1SUB WOOFER1VIDEO & AUDIO2VIDEO & AUDIO3AUTO SELECT12H, V PROTECTOR3
NONONO
13 |
ACEC
