29WV30
CUT OFF POINT
remote controller.left) black of the window pattern to sink.
signal or equivalent signal.Use "Y" of Minolta colour analyzer CA-100 in adjustment.
*Receive the crosshatch pattern1.Make the image normal with the2.Adjust the 3rd (1 thru 5 from theNote:
10-2
Adjustment Condition / ProcedureWaveform or othersbeam current 1,500 ? 50?A or more for 30 min or more.
standard mode.troller.and TP1602. Ammeter full scale: 3mA range Connect the TP1602 to the - side of the am- meter. Connect the TP1601 to the + side of the am- meter.with R1759 (sub-contrast VR).put.troller. (AV mode: DYNAMIC)the remote controller, and adjust the right dark white area of the window pattern to 2.7 ? 0.3cd.put.troller.with the remote controller, and adjust 50% white to 110 ? 3cd.
1.Receive the Monoscope pattern signal with2.Make the image normal with the remote con-3.Connect the beam ammeter between TP16014.Adjust the beam current to 1.6mA ? 50?ANote:Apply the adjustment after aging with the(On the white or green monocolour screen.)1.Receive the window pattern signal with AV in-2.Make the image normal with the remote con-3.Select the sub-bright adjustment mode with1.Receive the window pattern signal with AV in-2.Make the image normal with the remote con-3.Select the SUB-CONTRAST adjustment mode
CUT OFF, BKGD, SUB-CONT ADJUSTMENT
2C BUSC BUS
Adjustment pointMAX BEAM R1759BRIGHTNESS ADJUSMENT (ICONTROL) (AV SIGNAL)CONTRAST2IADJUSTMENT (AV SIGNAL)
34SUB-5SUB-
No.
" KEY
DOWN"4" KEYDOWN"5" KEYDOWN"6" KEYY: 0.275
DOWN"DOWN"0" KEY
on the shipment initial setting ta- ble.
On the monocolour screen of white or green.Note: R CUT OFFUP"1" KEYG CUT OFFUP"2" KEYB CUT OFFUP"3" KEYData up/down is possible with the above comparison. *12,300!KX: 0.272(With Monolta colour thermometer CA-100) Note: G-DRIVEUP"7" KEYB-DRIVEUP"8" KEYData up/Down is possible with the above comparison. *The colour temperature is based
10-1
the beam current 1,500 ? 50?A or more for 30 min or more.
Adjustment Condition / ProcedureWaveform or othersbeam current 1,500 ? 50?A or more for 30 min or more. (On the white or green Monocolour screen.)
signal.ice mode.lect the lateral in-line mode.first lighting lateral in-line raster to slighly light.and coarsely adjust the lateral in-line to be- come white. (Note)to the point where the lateral in-line raster goes out. Note :Apply the adjustment after aging withlect the normal mode.Signal.and TP1602.1.6mA with R1759 (Sub-Contrast VR)(PAL burst is generated with the signal gen- erator.)the colour temperature 12,300!K of the white peak to white.12,300!K with R-cut off, G-cut off and B-cut off.peak.
1.Receive the White Pattern with Colour Burst2.Select P-NORM with the remote controller. 3.Select the CUT OFF BKGD mode at the serv-4.Select the screen VR 0/10. 5.Press "-/--" key of the remote controller to se-6.Turn the screen VR clockwise, and adjust the7.Adjust the CUT OFF data of two other colours,8.Turn the screen VR in the opposite direction9.Press "-/--" key of the remote controller to se-1.Receive the White Pattern with Colour Burst2.Select P-NORM with the remote controller. 3.Connect the beam ammeter between TP16014.Coarsely adjust the beam current to approx.5.Receive the window pattern with AV input.6.With the data of G-drive and B-drive, adjust7.Adjust the right dark area of the window to8.Readjust the colour temperature at the white9.Check 12,300!K at the low white. Note:Apply this adjustment after aging with the
CUT OFF, BKGD, SUB-CONT ADJUSTMENT
2C BUSC BUS
Adjustment pointCRT CUTOFF ADJUSTMENT (I CONTROL)BALANCE BACK- GROUND2IADJUSTMENT (AV SIGNAL)
12WHITE
No.
10 |
ACEC
