[07]SIMULATIONS.fm 1 I 2379äa?7?
? e79a 1
[7] SIMULATIONSMain Sub Contents
codecode
1. Entering the simulation mode2401Jam total counter clear
02Trouble memory clear
Perform the following procedure to enter the simulation mode.
"#" key Interrupt key "C" key Interrupt key 04SPF counter clear
Main code Start key Sub code Start key06Paper feed counter clear
07Drum counter clear
2. Canceling the simulation mode08Copy counter clear
When the clear all key is pressed, the simulation mode is cancelled.09Printer counter clear
When the interruption key is pressed, the process is interrupted and the13Scanner counter clear
screen returns to the sub code entering display.14SPF jam total counter clear
*After canceling the simulation mode, be sure to turn OFF/ON the15Scanner mode counter clear
power and check the operation.
2501Main motor operation check
Note: If the machine is terminated by a jam error or paper empty during10Polygon motor operation check
copying in the adjustment by the simulation, recopying is required.
2602Size setting
05Count mode setting
3. List of simulations06Destination setting
Main Sub Contents07Machine condition check (CPM)
codecode18Toner save mode setting
0101Mirror scanning operation30CE mark conformity control ON/OFF
02Mirror home position sensor (MHPS) status display38Cancel of stop at drum life over
06Mirror scanning operation aging39Memory capacity check
0201Single paper feeder (SPF) aging42Transfer ON/OFF timing control setting
02SPF sensor status display43Side void amount setting
03SPF motor operation check51Copy temporary stop function setting
08SPG paper feed solenoid operation check 3001Paper sensor status display
11SPF PS release solenoid operation check 4301Fusing temperature setting
0302Shifter sensors status display10Postcard paper feed cycle setting (Japan only)
03Shifter operation check11Postcard size paper fusing temperature setting (Japan only)
11Shifter home position check12Standby mode fusing fan rotation setting
0501Operation panel display check 13Fusing paper interval control allow/inhibit setting
02Fusing lamp and cooling fan operation check 4434Transfer current setting
03Copy lamp lighting check 40Setting of rotation time before toner supply
0601Paper feed solenoid operation check 4601Copy density adjustment (300dpi)
02Resist roller solenoid operation check02Copy density adjustment (600dpi)
10Main cassette semicircular roller cleaning09Copy exposure level adjustment, individual setting (Text) 300dpi
0701Warm-up display and aging with jam10Copy exposure level adjustment, individual setting (Text) 600dpi
06Intermittent aging11Copy exposure level adjustment, individual setting (Photo) 600dpi
08Shifting with warm-up display 18Image contrast adjustment (300dpi)
0801Developing bias output19Exposure mode setting
02Main charger output (Grid = HIGH)(Gamma table setting/AE operation mode setting/
Photo image process setting)
03Main charger output (Grid = LOW)
06Transfer charger output20SPF exposure correction
29Image contrast adjustment (600dpi)
10-Toner motor operation
14-Trouble cancel (except for U2) 30AE limit setting
31Image sharpness adjustment
16-U2 trouble cancel
2203Jam memory display4801Main scanning magnification ratio adjustment
05SPF/RSPF mode sub scanning magnification ratio
04Jam total counter display
05Total counter displayadjustment in copying
4901Flash ROM program writing mode
08SPF counter display
09Paper feed counter display5001Image lead edge adjustment
06Copy lead edge position adjustment (SPF)
12Drum counter display
13CRUM type display10Paper off-center adjustment
12Document off-center adjustment
14P-ROM version display
15Trouble memory display5102Resist amount adjustment
5308SPF scanning position automatic adjustment
17Copy counter display
18Printer counter display10SPF scan position change-over setting
6103HSYNC output check
19Scanner mode counter display
21Scanner counter display6301Shading check
07SPF automatic correction
22SPF jam counter display
6401Self print
AL-1633/1644 SIMULATIONS 7-1 |
ACEC
