CodeCode
FunctionFunction
MainSubMainSub
221Used to check the counter value of each section.2614Used to input the Software Key for the PS
2Used to check the total numbers of misfeed and extention kit.
troubles. (When the number of misfeed is 18Used to set enable/disable of toner save operation.
considerably great, it is judged as necessary for 20Used to set the job separator paper exit mode.
repair. The misfeed rate is obtained by dividing this 22Used to set the specification (language display) for
count value with the total counter value.)the destination.
3Used to check the misfeed positions and the 30Used to set the operation mode for CE mark.
number of misfeed at each position. (When the 35Used to set the mode of trouble memory.
number of misfeed is considerably great, it can be 36Used to set whether to stop when the maintenance
judged as necessary for repair.)life is reached.
4Used to check the total trouble (self diag) history.
37Used to set whether to stop when the developer
5Used to check the ROM version of each unit
life is reached.
(section).
38Used to set whether to stop when the drum life is
7Used to display the key operator code
reached.
8Used to check the number of use of the staple, the
46Used to set whether to meet with the output
SPF, and scanning.
direction of images regardless of the mode when
9Used to check the number of use of each paper installing the finisher.
feed section. (the number of prints)
50Used to set whether to use the black/white reverse
10Used to check the system configulation.function.
11FAX related counter display54Used to set the PWM duty (brightness) at the
12Used to check the misfeed positions and the center value of the LCD contrast.
number of misfeed at each position. (When the 57Used to set the model code.
number of misfeed is considerably great, it can be
60Used to set enable/disable of the FAX mode key
judged as necessary for repair.)
when FAX is not installed. (When FAX is installed,
19Used to display the scanner mode counter.the FAX mode is enabled regardless of this setup.)
241Used to clear the misfeed counter, the misfeed 271Used to set PC/MODEM communication trouble
history, the trouble counter, and the trouble history. (U7-00) detection Yes/No.
(The counters are cleared after completion of
5Used to enter the TAG No. of the copier.
maintenance.)
301Used to check the operation of sensors and
2Used to clear the number of use (the number of
detectors in the sections other than the paper feed
prints) of each paper feed section.
section of the copier and the related circuit. (The
3Used to clear the number data of use of the staple, operation of sensors and detectors can be
the SPF and scanning.monitored with the LCD.)
4Used to reset the maintenance counter.2Used to check the operation of sensors and
5Used to reset the developer counter. (The detectors in the paper feed section and the related
developer counter of the DV unit which is installed circuits. (The operations of sensors and detectors
is reset.)in the paper feed section can be monitored with
6Used to reset the copy counter.the LCD.)
7Used to clear the OPC drum (membrane 401Used to check the operation of the manual paper
decrease) correction counter. (This simulation is feed tray paper size detector and the related
executed when the OPC drum is replaced.circuit. (The operation of the manual paper feed
9Used to clear the printer print counter. (The tray paper size detector can be monitored with the
counter is cleared after completion of LCD.)
maintenance.)2Used to adjust the manual paper feed tray paper
10FAX related counter clearwidth detector detection level.
15Used to clear the scanner mode counter.3The AD conversion value of manual feed width
251Used to check the operation of the main drive detection is displayed.
(excluding the scanner section) amd to check the 411Used to check the document size detection photo
operation of the toner concentration sensor. (The sensor.
toner concentration sensor output can be 2Used to adjust the detection level of the document
monitored.)size photo sensor.
2Used to make the initial setting of toner 3Used to check the light reception level and the
concentration when replacing developer.detection level of the original size detection photo
261Used to set options. (This simulation is used to sensor.
make option setting when an option is installed.)4Used to adjust the detection level of OC 20
2Used to detect the paper size.degrees.
3Used to set the specifications of the auditor. 431Used to set the fusing temperature in each
Setting must be made depending on the use operation mode.
condition of the auditor.10Used to set the paper feed cycle for postcard.
5Used to set the count mode of the total counter 441Used to make various setups in each mode of
and the maintenance counter.process control.
6Used to set the specifications depending on the 34Used to adjust the transfer current value.
destination.35Correction temperature setup when correcting the
10Used to enter the Software Key for the Network ambient temperature.
Scanner. (Setup is allowed only when the PCL 40Used to set the rotating time before toner supply.
board is installed.
12Used to input the Software Key for E-MAIL RIC.
AR-235/275 SIMULATION - 4 |
ACEC
