46-20
SIMULATION 46-20
PurposeAdjustmentOC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
FunctionUsed to adjust the copy density correction in the 2.EXP LEVEL 1
(Purpose)SPF copy mode for the document table copy 3.SPF(ODD) 1281
4.SPF(EVEN) 128
mode. The adjustment is made so that the copy
5.DSPF 128
density becomes the same as that of the
document table copy mode. Select other than 0 - 2, and press [START] key.
Press [CUSTOM SETTINGS] key.
SectionSPF
ItemPicture qualityDensitySIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS
Operation/Procedure
START.
(Adjustment mode selection)3.SPF(ODD)
128
1) Select the number corresponding to the copy mode to be
adjusted with 10-key.Select 1, Press [START] key. Press [CUSTOM SETTINGS] key,
and press
or terminate copying.
SPF odd pixel (Front surface copy), SPF even pixel (Front sur-[START] key.
face copy), SPF (Back surface copy) (Select one of 3 - 5.)
SIMULATION 46-20
2) Press [SATART] key.OC/SPF EXP. ADJUSTMENT. NOW PRINTING.
(Copy density level adjustment)
Select 0, and Press [START] key or
1) Enter the density correction value with 10-key.press [START] key.press [CUSTOM SETTINGS] key.
2) Press [P] key or [START] key.SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-5, AND PRESS START.
(Copy condition setting in this simulation)
(FEED TRAY)
To select paper (paper feed tray), perform the following proce- 2.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
dures.1
1) Enter 0 with 10-key. Select 2, and
Press [START] key or
press [START] key.
2) Press [START] key. (The mode is changed to the paper feedpress [CUSTOM SETTINGS] key.
tray selection mode.)
SIMULATION 46-20
3) Enter the number corresponding to the paper feed tray to beOC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
used with 10-key.
3.1.0 4.1.5 5.2.0
4) Press [START] key. (The paper feed tray is selected.)6.2.5 7.3.0 8.3.51
9.4.0 10.4.5 11.5.0
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
46-21
copying is performed.
PurposeAdjustment
Set
ItemContentDefaultFunctionUsed to adjust the scanner exposure level in all
range
(Purpose)the scanner modes.
0 TRAY SELECT Paper feed tray selection--
ItemPicture qualityDensity
1: TRAY1
Operation/Procedure
2: TRAY2
3: TRAY31) Select "SCANNER EXP. LEVEL" with 10-key.
4: TRAY42) Press [START] key.
5: Manual feed
3) Enter the image density adjustment value.
1 PRINT START Print start (Default)--
4) Press [P] key or [START] key.
2 EXP LEVELExposure level selection--
NOTE: When this simulation is performed to adjust the scan image
3: Exposure level 1.0
densities, all the image densities in all the scan modes are
4: Exposure level 1.5
changed to the image density level set with this simulation.
5: Exposure level 2.0
That is, the image densities set with SIM 46-22, 23, 24, 25,
6: Exposure level 2.5
and 45 are changed to the image density level set with this
7: Exposure level 3.0
simulation.8: Exposure level 3.5
9: Exposure level 4.0Set
ItemDefault
10: Exposure level 4.5range
11: Exposure level 5.0
0 SCANNER EXP. LEVEL Image density level 0 - 9950
3 SPF (ODD)SPF (front) (odd pixel)0 - 255 128
NOTE: Only the set value is changed and no printing is performed.
4 SPF (EVEN)SPF (front) (even pixel)
5 DSPFDSPF (Back surface)
"Set value - 128" is added to the shading adjustment value (SIM
46-17).
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 46 |
ACEC
