B. Simulation listCode
Function (Purpose)
Main Sub
(1) Main/ Sub
130Used to cancel the self-diag "U1" trouble. (Only
Codewhen FAX is installed.)
Function (Purpose)
Main Sub
140Used to cancel excluding the self-diag U1/LCC/
11Used to check the operations of the scanner U2/PF troubles.
(read) unit and its control circuit.
150Used to cancel the self-diag "U6-01, 02, 03, F3-
2Used to check the operation of sensor and 12, 22" (large capacity paper feed tray, paper
detector in the scanning (read) section and the feed trays 1, 2) troubles.
related circuit.
160Used to cancel the self-diag U2 troubles.
21Used to check the operations of the automatic
170Used to cancel the PF troubles (when the copy
document feeder unit and the control circuit.
inhibit command from the host computer is
2Used to check the operations of the sensors and received).
detectors in the automatic document feeder unit 211Used to set the maintenance cycle.
and the related circuits.221Used to check the print count value in each
3Used to check the operations of the loads in the section and each operation mode. (Used to check
automatic document feeder unit and the control the maintenance timing.)
circuits.2Used to check the total numbers of misfeed and
32Used to check the operation of sensor and troubles. (When the number of misfeed is
detector in the finisher and the related circuit.considerably great, it is judged as necessary for
3Used to check the operation of the load in the repair. The misfeed rate is obtained by dividing
finisher and the control circuit.this count value with the total counter value.)
6Used to adjust the stacking capacity of the 3Used to check misfeed positions and the misfeed
finisher. (Used to adjust the alignment plate count of each position. (If the misfeed count is
(jogger) stop position in the finisher paper width considerably great, it may be judged as
direction. The adjustment is made by changing necessary to repair.)
the alignment plate home position in the paper
4Used to check the trouble (self diag) history.
width direction by software.)
5Used to check the ROM version of each unit
10Console finisher (AR-FN7) adjustment
(section).
20Used to check the mail bin stacker sensor.
6Used to output the list of the setting and
21Used to check the operations of the mail bin adjustment data (simulations, FAX soft switch,
stacker loads.counters).
42Used to check the operations of the sensors and 7Used to display the key operator code. (This
detectors in the paper feed section (desk paper simulation is used when the customer forgets the
feed/large capacity tray) and the related circuit.key operator code.)
3Used to check the operations of the loads in the 8Used to check the number of use of the finisher,
paper feed section (desk paper feed/large the SPF, and the scan (reading) unit.
capacity tray) and the related circuit.
9Used to check the number of use (print quantity)
51Used to check the operation of the display, LCD of each paper feed section.
in the operation panel, and control circuit.
10Used to check the system configuration (option,
2Used to check the operation of the heater lamp internal hardware).
and the control circuit.
11Used to check the use frequency (send/receive)
61Used to check the operation of the paper of FAX. (Only when FAX is installed)
transport system loads and the control circuit.
12Used to check the SPF misfeed positions and the
2Used to check the operations of each fan motor number of misfeed at each position. (When the
and its control circuit.number of misfeed is considerably great, it can be
71Used to set the operating conditions of aging.judged as necessary for repair.)
6Used to set the intermittent aging cycle.13Used to check the operating time of the process
8Used to set the warm-up time display YES/NO.section (OPC drum, DV unit, toner bottle).
81Used to check and adjust the operations of the 19Used to check the values of the counters related
developing voltage of each color and the control to the scan mode and the internet FAX mode.
circuit.232Used to check the trouble history of paper jam
2Used to check and adjust the operation of the and misfeed. (If the number of misfeed and
main charger grid voltage in each printer mode troubles is considerably great, it may be judged
and the control circuit.as necessary to repair.)
6Used to check and adjust the operation of the 80Used to check the operations of the sensors and
transfer voltage and the control circuit.detectors in the paper feed and transport section.
17Used to check and adjust the operation of the 241Used to clear the misfeed counter, the misfeed
transfer voltage and the related circuit. (Transfer history, the trouble counter, and the trouble
belt cleaning mode)history. (The counters are cleared after
91Used to check and adjust the operation of the completion of maintenance.)
load (clutch/solenoid) in the duplex section and 2Used to clear the number of use (the number of
the control circuit.prints) of each paper feed section.
2Used to check the operations of the sensors and 3Used to clear the number of use of the finisher,
detectors in the duplex section and its control SPF, and the scan (reading) unit.
circuit.4Used to reset the maintenance counter.
101Used to check the operations of the toner motor 5Used to reset the developer counter. (The
and the related circuit.developer counter of the DV unit which is installed
is reset.)
AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 3 |
ACEC
